Battery Charge Controller Protection Switch Digital Display On Off Relay Charge Controller for 12V 24V Battery

#ad
CPTDCL #ad - Easy to operate- with the start button and stop button, you can set the start charging voltage and the stop charging voltage, DUAL PROTECTION. Applicable to a variety of situations: new energy battery, car battery, electric car battery, lithium ion battery ATTENTION: The default start charging voltage is 12V, lead acid battery, Ni-MH batteries, nickel cadmium battery, stop charging voltage is 14V.

Automatic charge and discharge, protect/ prolong battery life, save energy. 2. How to set stop stop charging voltage: when it is in charging status, press the stop button one time, it displays stop charging voltage. Long press the stop button 3seconds, the number flashing, then you can set the stop charging voltage with the start button and the stop button.

Battery Charge Controller Protection Switch Digital Display On Off Relay Charge Controller for 12V 24V Battery #ad - Low voltage disconnect module for 12v 24v battery with Overcharge Protection Product Parameters: input voltage:DC 10-30V accuracy:01v application range:12-24v Battery size information:82*58*18mm/ 3. 22*2. 28*7. 09in using guidance:when you set the charging voltage, you can press the start button to increase, press the stop button to decrease 1.

How to set start charging voltage: when it is in charging status, press the start button one time, it displays start charging voltage. Long press the start button 3seconds, the number flashing, then you can set the start charging voltage with the start button and the stop button.

More information about CPTDCL #ad

IS Icstation Digital Low Voltage Protector Disconnect Switch Over Discharge Protection Module for 12-36V Lead Acid Lithium Battery

#ad
icstation Digital Battery Low Voltage Protection #ad - Specifications: input voltage Range: DC12-36V Control Accuracy: 01v compatible battery: lead acid, lithium ion battery, solar panel batteryBoard Size: 57 X 42 X 19mm/2. 24 x 1. 65 x 075inchl*w*hpackage included:1x lead acid lipo battery charge controllerOperation Instructions:+: short press display the low voltage protection parameter, long press to change the protection parameter -: short press to display the difference value, long prss to change this parameter.

It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. E. G. Battery voltage lower than 11V will stop ouput and higher than 11. 6v start output. Long press "+" and set it as 11, then long press "-" and set it as 0

IS Icstation Digital Low Voltage Protector Disconnect Switch Over Discharge Protection Module for 12-36V Lead Acid Lithium Battery #ad - 6v. Warm prompt ❤❤-----------1, we provide the using guidance by email, and replace service for free in case you received a defective one, please rest assured to buy it.2, discount price and faster delivery way for bulk purchase. When the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime.

More information about icstation Digital Battery Low Voltage Protection #ad


Similar products



12V Battery Charging Controller Protection Board Module, Undervoltage Low Voltage Cut Off Automatic Switch Recovery Protection Controller Module

#ad
Walfront #ad - It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. Designed with a leD indicator to show if load is cut off or turned on. This protection board will help you to protect battery from over-discharging and prolong battery life.

When the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime. Display is accurate, the switch module is quickly to open and close when near minimum voltage; Settings is stored non-volatile, it can keep set when power off.

12V Battery Charging Controller Protection Board Module, Undervoltage Low Voltage Cut Off Automatic Switch Recovery Protection Controller Module #ad - Features: this is a under-voltage switch module used to turn off the power of load in the event of the voltage dropping below a set value. Specifications: suitable Battery Voltage: 12V Voltage Error: ±01v load current: 10a Size: 5*3*1. 7cm/2. 0*1. 2*07in weight: 21gapprox. Package includes: 1 x protection board Programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery.

More information about Walfront #ad


Similar products



IS ICStation Digital Low Voltage Protector Disconnect Switch Over Discharge Protection Module for 12-34V Lead Acid Lithium Battery Pack of 2

#ad
icstation Digital Battery Low Voltage Protection #ad - E. G. It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. 3, please send us an email when you meet problems in using or delivery, your inquiry will be answer within 12 hours in business days, always at your service! Programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery.

Display is accurate, the switch module is quickly to open and close when near minimum voltage; Settings is stored non-volatile, it can keep set when power off. On-board momentary push button to set the low voltage disconnect parameter, when the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime.

IS ICStation Digital Low Voltage Protector Disconnect Switch Over Discharge Protection Module for 12-34V Lead Acid Lithium Battery Pack of 2 #ad - Specifications:input voltage Range: DC12V-36V Control Accuracy: 01v compatible battery: lead acid, lithium ion battery, solar panel batteryBoard Size: 57 X 42 X 19mm/2. 24 x 1. 65 x 075inchl*w*hpackage included:2 packs X Lead Acid Lipo Battery Charge Controller; pack of 2 is more cost-effective. Board size: 57 x 42 x 19mm/2.

More information about icstation Digital Battery Low Voltage Protection #ad


Similar products



Electronics-Salon Low Voltage Disconnect Module LVD, 12V 10A, Protect/Prolong Battery Life.

#ad
Electronics-Salon EXPSFD005865 #ad - Board size: 57 x 42 x 19mm/2. 24 x 1. 65 x 075inchl*w*h, input voltage range: dc12-36v, power consumption:. It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. Din rail mount version can support width 35 / 32 / 15mm rails.

Mount type: panel mount. The item no paper instructions, please download the PDF file, and before buying please read the file: http://www. Audiowind. Com/new-pdf/d1021-d1077series. Pdf to protect electronics from damaging low voltages and prevent a deep discharge of a battery during an extended power outage, the LVD module will automatically disconnect the battery when the voltage falls below the user adjustable cutoff voltage.

Electronics-Salon Low Voltage Disconnect Module LVD, 12V 10A, Protect/Prolong Battery Life. #ad - Suitable battery: 12V. Red-green led indication for relay switch ON and OFF. Low voltage disconnect module LVD, 12V 10A, Protect/Prolong Battery Life. Features: programmable voltage setting for Disconnect and Reconnect. When power is restored the Smart Switch will automatically reconnect the battery. Applications include: solar systems, Alarm systems, Mobile systems, UPS systems, Or any application where you need to protect the battery from total discharge.

More information about Electronics-Salon EXPSFD005865 #ad


Similar products



DROK DC Buck Module, Adjustable Buck Converter Step Down Voltage Regulator 6V-32V 30V 24V 12V to 1.5-32V 5V 5A LCD Power Supply Volt Reducer Transformer Module Board with USB Port Protective Case

#ad
DROK #ad - F-1 mode: display input voltage 3. Current regulation can only be performed in the status of constant current. Package included: 1x dc buck module 4x copper cylinder screws m3*6 4x double-pass Screws M3*12 8x Roundhead Screws M3*6 Programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery.

When the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime. Please reduce the power when voltage difference is large. Please add a diode when used for charging. Installation: 8x pillars, 8x 3mm screws Wire Connection: terminal block or soldering terminals; VIN is input; VOUT is output.

DROK DC Buck Module, Adjustable Buck Converter Step Down Voltage Regulator 6V-32V 30V 24V 12V to 1.5-32V 5V 5A LCD Power Supply Volt Reducer Transformer Module Board with USB Port Protective Case #ad - Over 3a or 35w, please enhance heat dissipation. Constant current requires an output voltage of above 2V to be adjusted. Parameters: chip: mp2304 input voltage: 6~32V Output voltage: 1. 5~32v continuously adjustable Input should be 1. 5v higher than output. Output current: 5A max, adjustable, recommended use within 4.

5a. It's a protection switch module, not included batteries itself.

More information about DROK #ad


Similar products



2PCS Temperature Controller Module with Case, XH W1209 Display Digital Thermostat Module with Waterproof NTC Probe -50~110℃ Electronic Temperature Temp Control Module Switch

#ad
UMLIFE #ad - P0 :cooling / heating; range: c/h; default: C P1 :Hysteresis Setting; Range:01-15; default: 2 p2 :highest setting limit; range:110; default: 110 p3: lowest setting limit; range:-50; default: -50 p4 :temperature correction; range:-7~7℃; default: 0℃ p5: delay start time; Range:0-10 Minute; Default: 0 P6: High Temperature Alarm; Range:0-110; Default: Off When the Thermostat is power off, long press "- or +", you can restore the factory settings   Specification: Temperature Control Range: -50 ~ 110℃ Resolution at -9.

9 to 99. 9: 01℃ resolution at all other temperatures: 1℃ Measurement Accuracy: 01℃ control Accuracy: 01℃ refresh Rate: 05 seconds input power dc: 12v Measuring Inputs: NTC 10K 05% waterproof Sensor: 05m output: 1 channel relay output, capacity: 10A   Power Consumption: Static Current:. With this module, you can intelligently control power to most types of electrical device based on the temperature sensed by the included high accuracy NTC temperature sensor.

2PCS Temperature Controller Module with Case, XH W1209 Display Digital Thermostat Module with Waterproof NTC Probe -50~110℃ Electronic Temperature Temp Control Module Switch #ad - Although this module has an embedded microcontroller no programming knowledge is required. The current temperature is displayed in degrees Centigrade via its 3 digit seven segment display and the current relay state by an on board LED. 3 tactile switches allow for configuring various parameters including on & off trigger temperatures.

More information about UMLIFE #ad


Similar products



HiLetgo 5pcs DC-DC Buck Step Down Module 6-24V 12V/24V to 5V 3A USB Charger Module Arduino

#ad
HiLetgo #ad - Dc-dc buck step down module 6-24v 12v/24v to 5v 3a usb charger module arduino Description: High quality USB port, Output voltage indicator RED Small size, 26. 4 l * 15 w * 7. 4 h mm, input with reverse polarity protection diode, will not damage when input connect incorrect, Ultra-low static current, 0.85 ma only.

Display is accurate, the switch module is quickly to open and close when near minimum voltage; Settings is stored non-volatile, it can keep set when power off. Do not need to add swith when connected to the car battery, can be connected to car cigarette lighter cable or ACC power supply cable Module Parameters: Module Properties: non-isolated buck module BUCK synchronous rectification Input voltage: DC 6-24VOutput voltage: 5.

1-5. 2v output current: 3a max please enhance heat dissipation when full load using, the actual test result input 12V output current 2A do not need to enhance heat dissipation. When the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime.

HiLetgo 5pcs DC-DC Buck Step Down Module 6-24V 12V/24V to 5V 3A USB Charger Module Arduino #ad - Full load temperature: 30 ° CStatic current: 085 ma load regulation: ±1%Voltage Regulation: ±05% dynamic response speed: 5% 200usinput reverse polarity protection: yes, there is reverse polarity protection diodeConnection mode: WeldingInput mode: Welding Output mode: USB Package Including: 5 * USB DC-DC Step Down Module Programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery.

It's a protection switch module, not included batteries itself.

More information about HiLetgo #ad


Similar products



12V Battery Low Voltage Cut Off Switch On Protection Undervoltage Controller Under-Voltage Control

#ad
GLOGLOW #ad - It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. Display is accurate, the switch module is quickly to open and close when near minimum voltage; Settings is stored non-volatile, it can keep set when power off.

Package includes: 1 x battery under-voltage Controller Programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery. When the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime.

12V Battery Low Voltage Cut Off Switch On Protection Undervoltage Controller Under-Voltage Control #ad - Specifications: suitable battery: 12V storage/lithium battery Control Current: 20A Control Precision: 01v voltage error: ¡À01v size: 8*4. 3*2. 8cm/3. 1*1. 7*1. 1in weight: 41gapprox. Restore to factory setting: at normal state, press and hold S 1 and S 2 buttons together, till display shows 888, to restore to factory setting.

Board size: 57 x 42 x 19mm/2.

More information about GLOGLOW #ad


Similar products



Timer Relay, DROK Time Delay Relay DC 5V 12V 24V Delay Controller Board Delay-off Cycle Timer 0.01s-9999mins Trigger Delay Switching Relay Module with LCD Display Support Micro USB 5V Power Supply

#ad
DROK 200350 #ad - It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. Product parameters: working voltage: DC 6V~30V, support micro USB 5. 0 v power supply Working current: 50mA.

Board size: 57 x 42 x 19mm/2. 24 x 1. 65 x 075inchl*w*h, input voltage range: dc12-36v, power consumption:. Static current: 15mA Max. Package includes: 1* 12v timer relay programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery. Trigger signal source: High level trigger 3.

Timer Relay, DROK Time Delay Relay DC 5V 12V 24V Delay Controller Board Delay-off Cycle Timer 0.01s-9999mins Trigger Delay Switching Relay Module with LCD Display Support Micro USB 5V Power Supply #ad - 0v~24. 0v, low level trigger 00v ~02v, switching value control potential free contact service life: more than 100, 000 times Working temperature: -40-85°C Additional Functions: aAutomatically hibernation function/ Low power function: In the running interface, long press STOP to open or close automatically sleep function.

When the battery voltage reach the setting values, the module will disconnect load automatically to aviod the battery from over discharging to prolong the battery lifetime. Cparameters view: in the operation interface, short press SET to display the current parameter setting in the system, without affecting the system normal operation.

Display is accurate, the switch module is quickly to open and close when near minimum voltage; Settings is stored non-volatile, it can keep set when power off.

More information about DROK 200350 #ad


Similar products



KNACRO 30A Battery Charge Controller Protection Switch DC 6V 12V 24V 36V 48V 6V-60V Battery Protection Board for Lead Acid Battery and Lithium Battery

#ad
KNACRO #ad - On-board momentary push button to set the charging initiation voltage and charging stop voltage, when the battery voltage reaches the setting value, the module will disconnect the charging circuit automatically to aviod the battery from overching to prolong the battery lifetime. 2> knacro provide you various kinds of great products at the lowest possible prices, welcome to our store and get what you want !!! Programmable battery low voltage disconnect switch for DC12-36V lead acid battery and lithium ion battery.

3, connect the appropriate voltage charger, you can charge the battery 5, long press flash to set lower limit voltage 4, press - to display lower limit voltage, Normally press Set to close the screen. Package included: 1x lead acid lipo Battery Charge Controller If you have any question, please feel free to contact us.

KNACRO 30A Battery Charge Controller Protection Switch DC 6V 12V 24V 36V 48V 6V-60V Battery Protection Board for Lead Acid Battery and Lithium Battery #ad - Board size: 57 x 42 x 19mm/2. 24 x 1. 65 x 075inchl*w*h, input voltage range: dc12-36v, power consumption:. It's a protection switch module, not included batteries itself. On-board momentary push button to set the low voltage disconnect parameter and 3 digit red LED display the parameter easy to operation. Display is accurate, the switch module is quickly to open and close when near minimum voltage; Settings is stored non-volatile, it can keep set when power off.

Our aim is to provide top Level Customer Service, so we will try our best to solve any problem.

More information about KNACRO #ad


Similar products