Can be used in 12v battery, 36V battery, 24V battery, 48V battery. Automatic charge and discharge, protect/ prolong battery life, save energy. Easy to operate- with the start button and stop button, you can set the start charging voltage and the stop charging voltage, DUAL PROTECTION. Applicable to a variety of situations: new energy battery, ni-mh batteries, lead acid battery, lithium ion battery ATTENTION: The default start charging voltage is 12V, nickel cadmium battery, electric car battery, car battery, stop charging voltage is 14V.
Battery Charge Controller Protection Switch Digital Display On Off Relay Charge Controller for 48V 36V 24V 12V Battery - Low voltage disconnect module lvd digital display on off relay Charge Controller Size information: 54*81*24mm Product Parameters: input voltage:DC 6-60V accuracy:01v application range:12v battery, 48v battery using guidance:when you set the charging voltage, 36V Battery, 24V Battery, you can press the start button to increase, press the stop button to decrease 1.
How to set start charging voltage: when it is in charging status, press the start button one time, it displays start charging voltage. Long press the start button 3seconds, the number flashing, then you can set the start charging voltage with the start button and the stop button. 2.
More information about CPTDCL
6 Pack Mini MP1584EN DC-DC Buck Converter Adjustable Power Step Down Module 24V to 12V 9V 5V 3V 6 PackeBoot SE153 - Please check if the negative and positive terminals are accessed correctly before operating. When setting the parameter, please make sure output voltage is stable before using the module to avoid any possible damage. Please don't output short circuit, otherwise the board would burn out. It can be minute adjustments to achieve a precise voltage.
Tips: please check if the product package is intact before opening. Package includes: 6 x mini mp1584en dc to dc buck converter You can adjust the voltage by placing a multi-meter on the output, synchronously, using a screw driver to adjust a potentiometer. Eboot mini mp1584en dc to dc buck converter adjustable power step down module 24V to 12V 9V 5V 3V, 6 Pack Specifications: Input voltage: 4.
6 Pack Mini MP1584EN DC-DC Buck Converter Adjustable Power Step Down Module 24V to 12V 9V 5V 3V 6 Pack - 5 v to 28 v output voltage: 08 v to 20 v output current: 3 a maximum conversion efficiency: 92% maximum Output ripple: less than 30 mV Switching frequency: 1. 5 mhz highest, monitor power supply, communications equipment supply, camera power supply, power buggies, car power, typically 1 MHz Operating temperature: -45 ℃ to 85 ℃ Size: 22 mm by 17 mm by 4 mm Application: DIY mobile power, etc.
Output current: 3 A maximum; Conversion efficiency: 92% maximum. Please make sure that this module within its working range before using. Operating temperature: -45 ℃ to 85 ℃; size: 22 mm by 17 mm by 4 mm; warning: do not reverse the positive and negative terminals to avoid any possible damage; Do not use light load less than 10% of output power or without load.
The input voltage should not be over 28 V to avoid damage.
More information about eBoot SE153
5v Regulator, DROK 5pcs Mini Voltage Reducer DC 4.5-24V 12V 24V Step Down to 5V Buck Converter Board 3A Volt Step-Down Transformer Power Supply Module
IZOKEE D1 Mini NodeMcu Lua 4M Bytes WLAN WIFI Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini (Pack of 5) …
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
bayite 3 Wire 0.36" DC 0~30V Digital Voltmeter Gauge Tester Blue LED Display Panel Mount Car Motorcycle Battery Monitor Volt Voltage Meter with Reverse Polarity Protection Pack of 5
DIYhz 20Pcs High Knob 3 Pin 2 Position 1P2T SPDT Panel Mount Vertical Micro Slide Switches AC 125V 2A