Akozon 5841863597 - It has a balancing function that ensures that each battery unit is fully charged at the same time. Unique design】wiring is neat, avoiding right-angled lines and curveing the edges; reduce signal vias to avoid signal distortion and cross interference; the wiring identifications clear and easy to understand avoid misconnection.

Specifications: continuous discharge current: 35A Momentary Discharge Current: 100A Charge Voltage: 42V Charge Current: 8AMax. Overcharge Detection Voltage: 4. 28±005v overcharge protection Delay: 100mS Overcharge Cancel Voltage: 4. 08±005v balance Detection Voltage: 4. 2±0025v balance Cancel Voltage: 4. 2±0

Akozon Protection Board, 35A 36V BMS PCB Protection Board with Balance and Heat Dink for 18650 Li-ion Battery Cell - 05v balance current: 56±5mA Over-discharge Detection Voltage: 2. 55±008v over-discharge detection Delay: 50mS Over-discharge Cancel Voltage: 3. 0±01 overcurrent detection voltage: 150mv overcurrent detection delay: 15ms overcurrent protection current: 120±5a protection cancel condition: disconnect load short circuit Protection Condition: Outside Load Short Circuit Short Circuit Detection Delay: 200uS Protection Cancel Condition: Disconnect Load Main Circuit Conduction Internal Resistance: ≤15mΩ Working Current: ≤50uA Sleeping CurrentBattery Over-discharge: ≤10uA Operating Temperature:﹣30℃~﹢80℃ Size: 69×51.

More information about Akozon 5841863597

---

Pure Nickel Strip,10m 1Roll of 0.2x8mm Nickel Tap for 18650 26650 32650 AA Cell Battery Pack Spot Welding

Causin - 5. 99. 96% pure nickel Sheet Density is 8. 902, melting point :1453, boiling point :2732, Nickel Resistivity: 6.84 1. It is pure nickel strip, it is different with tin plated steel strips. And u can put the pure Nickel tab in saline water at least 24H. U will found it is not rust. 2. Nickel strip is 02 thickness. Width is 8mm.

Pure nickel is low internal resistance, High internal resistance. Pure nickel Tab Spe:1. Nickel Strip is 02 thickness. Width is 8mmpure Nickel: Nickel content is 99. 96%3. 3. 99. 96% pure nickel sheet density is 8. 902, boiling point :2732, melting point :1453, Nickel Resistivity: 6.84. 4. Pure nickel strips are mainly used in the battery welding and soldering field due to the fact that they can easily be soldered and welded; Pure nickel is widely used in our daily life due to its outstanding oxidation resistance, corrosion resistance, low resistance and high conductivity.

More information about Causin


Similar products

---

Finware 10 Pair XT60 XT-60 Male Female Bullet Connectors Power Plugs with Heat Shrink for RC Lipo Battery

Finware - Made from high-temp nylon and gold plated bullet connectors, both included in the injection mold at the time when forming the connector. Pure nickel is low internal resistance, High internal resistance. 4. Pure nickel strips are mainly used in the battery welding and soldering field due to the fact that they can easily be soldered and welded; Pure nickel is widely used in our daily life due to its outstanding oxidation resistance, corrosion resistance, low resistance and high conductivity.

99. 96% pure nickel sheet density is 8. 902, melting point :1453, boiling point :2732, Nickel Resistivity: 6.84. 10 pair high quality Female and Male XT60 Connectors. High temperature Nylon Material. 60 amp current Handling Bullet Connectors. 5. 1. It is pure nickel strip, it is different with tin plated steel strips.

Finware 10 Pair XT60 XT-60 Male Female Bullet Connectors Power Plugs with Heat Shrink for RC Lipo Battery - And u can put the pure Nickel tab in saline water at least 24H. U will found it is not rust. 2.

More information about Finware


Similar products

---

ZRM&E 10PCS 3x5 18650 Lithium Battery Holder Bracket 15 Cell DIY Battery Storage Box Protection Board 3P5S Fixed Combination Bracket Total 15 Holders

- This is 18650 cell container specially used for assembling 18650 li-ion battery. Hight quality fire retardant ABS material, low temperature resistance, heat resistance, excellent impact resistance, chemical resistance and electrical properties.4. Pure nickel strips are mainly used in the battery welding and soldering field due to the fact that they can easily be soldered and welded; Pure nickel is widely used in our daily life due to its outstanding oxidation resistance, corrosion resistance, low resistance and high conductivity.

. High temperature Nylon Material. 5. Heat shrink 2:1 both red and Black Included - 2 Feet Total. Specification: name: 18650 battery holder Style: 3x5 cell Material: ABS Color: Black Size: 101. 25x6075mmapprox Pore Size: 18. 35mm center Distance: 202mm feature: can be freely combined installation: Top and bottom piece to work Package: 10pcs 3x5 Cell 18650 lithium batteries spacer plastic holder bracket 1.

ZRM&E 10PCS 3x5 18650 Lithium Battery Holder Bracket 15 Cell DIY Battery Storage Box Protection Board 3P5S Fixed Combination Bracket Total 15 Holders - It is pure nickel strip, it is different with tin plated steel strips. And u can put the pure Nickel tab in saline water at least 24H. U will found it is not rust.

More information about


Similar products

---

10S 36V 40A Li-ion Battery Protection Board BMS PCB Module for Ternary Cobalt Acid with Balance Batteries Power Supply Tools

Hilitand - High temperature Nylon Material. Pure nickel is low internal resistance, High internal resistance. Heat shrink 2:1 both red and Black Included - 2 Feet Total. 60 amp current Handling Bullet Connectors. High performance: stable various protective functions for charging and discharging, such as overcharge protection, over-discharge protection and short circuit protection.

Balance function: it has balance function which would ensure each battery cell being fully charged at same time. Protect your batteries:Choosing the correct protection board and applying it appropriately is vital to the longevity your batteries. Use: suitable for diy combination of import batteries, can hold 15pcs 18650 cells, the unique design and smart solid frame can be an excellent protector for your lithium ion battery pack.

10S 36V 40A Li-ion Battery Protection Board BMS PCB Module for Ternary Cobalt Acid with Balance Batteries Power Supply Tools - Function: type 18650 belong to necessary support of high-end battery combination, convenient combination, can withstand high drop, fixed specifications, high strength support, easy to heat dissipation, and free combination. Advantage: with card slot at edge, match up firm, any size can joining together, with strong, and no need for other device connected by vibration test.

Application: with professional battery holder to replace the traditional general adhesive, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery. Its the best choice of the battery combination. Application range: the protection board is for 10 series Li-ion batteries, it can be used for ternary batteries, manganese acid batteries and cobalt acid batteries.

More information about Hilitand


Similar products

---

DIY Battery Pack PVC Heat Shrink Wrap Tube,Length 3M Flat Width 150±1MM for Big Battery Pack Power

Causin - 3. 4. Pure nickel strips are mainly used in the battery welding and soldering field due to the fact that they can easily be soldered and welded; Pure nickel is widely used in our daily life due to its outstanding oxidation resistance, corrosion resistance, low resistance and high conductivity. 1. It is pure nickel strip, it is different with tin plated steel strips.

And u can put the pure Nickel tab in saline water at least 24H. U will found it is not rust. 2. Nickel strip is 02 thickness. Width is 8mm. 60 amp current Handling Bullet Connectors. 5. Shrinkable plastic tube sleeve, sporting goods, toys, electronics, Applications include insulation and jacketing of batteries, capacitors and similar objects-a vast range of applications in the production of industrial equipment, and consumer products.

DIY Battery Pack PVC Heat Shrink Wrap Tube,Length 3M Flat Width 150±1MM for Big Battery Pack Power - 4. Pvc heat shrink tubing is a thin-wall, low cost material offering good electrical and mechanical characteristics. Pvc heat shrink Wrap Spec :1. Flat width is 150±3mm, Length is 3M. Thickness is 0

More information about Causin


Similar products

---

Baimeixun 20pcs 4x5 Cell Spacer 18650 Lithium Battery Plastic Holder Bracket

Baimeixun - Xt-60 connector for rc Lipo Batteries Drones Airplanes Cars Vehicles. Type: 10pcs 3x5 cell 18650 lithium batteries spacer plastic holder combination mounting bracket. High temperature Nylon Material. 4. Pure nickel strips are mainly used in the battery welding and soldering field due to the fact that they can easily be soldered and welded; Pure nickel is widely used in our daily life due to its outstanding oxidation resistance, corrosion resistance, low resistance and high conductivity.

. Material: abs plastic + poly-carbonate Size Approx: 10 * 8 * 08cm/3. 94" * 3. 15" * 031" pore size: 18. 4 mm suitable for all types of battery assembly type 18650 belong to necessary support of high-end battery combination, easy to heat dissipation, and free combination With professional battery holder to replace the traditional general adhesive, can withstand high drop, fixed specifications, high strength support, which would brings convenient combination and more firm connection, convenient combination, as well as brings convenient maintenance of the battery.

Baimeixun 20pcs 4x5 Cell Spacer 18650 Lithium Battery Plastic Holder Bracket - Its the best choice of the battery combination Package include:20 x lithium batteries Plastic holder 1. It is pure nickel strip, it is different with tin plated steel strips. And u can put the pure Nickel tab in saline water at least 24H. U will found it is not rust.

More information about Baimeixun


Similar products

---

Amass 10 Pair XT90 XT-90 Male Female Bullet Connectors Power Plugs with Heat Shrink for RC Lipo Battery Motor

Amass - Heat shrink 2:1 both red and Black Included - 2 Feet Total. Used in RC battery and motor. Package included:  10 pairs Connectors10pcs male+10pcs female +2pcs heat shrink 1. It is pure nickel strip, it is different with tin plated steel strips. And u can put the pure Nickel tab in saline water at least 24H.

U will found it is not rust. 2. Nickel strip is 02 thickness. Width is 8mm. 4. Pure nickel strips are mainly used in the battery welding and soldering field due to the fact that they can easily be soldered and welded; Pure nickel is widely used in our daily life due to its outstanding oxidation resistance, corrosion resistance, low resistance and high conductivity.

Amass 10 Pair XT90 XT-90 Male Female Bullet Connectors Power Plugs with Heat Shrink for RC Lipo Battery Motor - Two pcs heat shrinks are also packed with the xt-90 connector together for your backup when you weld some cables. Wide application】often used in remote control aircraft and More RC models, RC ESCXT90 male, like some big RC lipo batteryXT90 Female, RC Charger and so on.5. Shrinkable plastic tube sleeve, toys, applications include insulation and jacketing of batteries, electronics, capacitors and similar objects-a vast range of applications in the production of industrial equipment, sporting goods, and consumer products.

4. Pvc heat shrink tubing is a thin-wall, low cost material offering good electrical and mechanical characteristics.

More information about Amass


Similar products

---

ZRM&E 40PCS 18650 Lithium Battery Triple Holder Bracket 3 Cell DIY Battery Storage Box Protection Board

- When exposed to heat in excess of102 degree for a few seconds, the specially formulated polyvinyl chloride material will shrink rapidly andȀ㯸Ȁ㯸 ⾯Ȁ䃸Ȁ䃸 クȀ磸Ȁ磸 ㆯȀ铸Ȁ铸 ㊯Ȁ꛸Ȁ꛸ ㎯Ȁ췸Ȁ췸 㒯Ȁ铹Ȁ铹 㖯Ȁ당Ȁ당 㚯Ȁ볹Ȁ볹 㞯Ȁ퓹Ȁ퓹 㢯 㢯. Very good flexibility.

With this holder, storage battery and electric car battery, electric tools battery, which can be used as electric bike battery, we can make different battery pack, etc. Two pcs heat shrinks are also packed with the xt-90 connector together for your backup when you weld some cables. Wide application】often used in remote control aircraft and More RC models, like some big RC lipo batteryXT90 Female, RC ESCXT90 male, RC Charger and so on.

ZRM&E 40PCS 18650 Lithium Battery Triple Holder Bracket 3 Cell DIY Battery Storage Box Protection Board - Type: 40pcs 3 cell 18650 lithium batteries spacer plastic holder combination mounting bracket. 5. 5. Shrinkable plastic tube sleeve, capacitors and similar objects-a vast range of applications in the production of industrial equipment, electronics, Applications include insulation and jacketing of batteries, sporting goods, toys, and consumer products.

4. Pvc heat shrink tubing is a thin-wall, low cost material offering good electrical and mechanical characteristics. Size:100 * 80 * 8 mm, pore size: 18. 4 mm.

More information about


Similar products

---

Hilitand Li-Ion Li-Polymer Battery Pack Protection Board Automatic Activation BMS Module for 13S 48V/54.6V Batteries

Hilitand - Makes your battery pack Solid and Reliable. 5. Shrinkable plastic tube sleeve, sporting goods, Applications include insulation and jacketing of batteries, capacitors and similar objects-a vast range of applications in the production of industrial equipment, toys, electronics, and consumer products.4. Pvc heat shrink tubing is a thin-wall, low cost material offering good electrical and mechanical characteristics.

. Material: abS plastic + Poly-carbonate. Specifications: overcharge Protection Single Battery Overcharge Detection Voltage 4. 25v±005v single battery Overcharge Release Voltage 4. 10v±005v charge protection rated charging current ≤5a Charging protection Current / Over-discharge Protection Single Battery Overcharge Detection Voltage 2.

Hilitand Li-Ion Li-Polymer Battery Pack Protection Board Automatic Activation BMS Module for 13S 48V/54.6V Batteries - 50v±005v single battery Overcharge Release Voltage 3. 00v±005v rated discharging current 15a discharging protection current 45±5a short circuit protection recovery Condition Disconnecting Load Inner Resistance B-,  P- conduction resistance ≤25mΩ Current Consumption Self-consumption ≤30uA Size L*W*H 60*34*10mm / 2.

More information about Hilitand


Similar products

---

Breynet 3M 0.1 x 8 mm 18650 Pure Ni Plate Nickel Welding Strip Tape 3 M For 18650 Battery Spot Welder/Welding

Breynet - Low resistivity good luster, ductility, weldability With anti-abrasion performance Good properties and electrical conductivity on the tin Packing Included:1pc x Nickel strip 1. It is pure nickel strip, it is different with tin plated steel strips. And u can put the pure Nickel tab in saline water at least 24H.

U will found it is not rust. 2. Nickel strip is 02 thickness. Width is 8mm. High temperature Nylon Material. Two pcs heat shrinks are also packed with the xt-90 connector together for your backup when you weld some cables. Wide application】often used in remote control aircraft and More RC models, like some big RC lipo batteryXT90 Female, RC ESCXT90 male, RC Charger and so on.

Breynet 3M 0.1 x 8 mm 18650 Pure Ni Plate Nickel Welding Strip Tape 3 M For 18650 Battery Spot Welder/Welding - Type: 40pcs 3 cell 18650 lithium batteries spacer plastic holder combination mounting bracket. Good properties and electrical conductivity on the tin. Advanced protective housings】the advanced protective housings of XT90 connector are better than traditional heat shrinks, as using these housings could simplify the welding process, avoiding the wire exposing outside, also make the connector have a good looking.

High safety performance】the housings of xt90 connectors could aviod the wire exposing outside, the production fully passed IOS9001 certification, CE, which also aviod the power hurt humans. In addition, ROHS. Last but not least, xt90 connector with fireproof material pass many certifications, such as UL, you totally could use it in safe.

More information about Breynet


Similar products

UPG 6543875488 - Pack of 3. Ub645 6v 4. 5ah - absorbant glass Mat AGM technology for superior performance. Rechargeable battery that can be mounted in any position, resists shocks and vibration. Upg #d5733 ub645 6v 4. 5ah. 1 year Warranty. Dimensions: 2. 78 inches x 1. 88 inches x 4. 18 inches. Valve regulated, spill proof construction allows safe operation in any position.

Sla/agm maintenance free, spill proof battery. Common uses for the ub645: consumer electronics, electric vehicles, access control devices, Portable Tools, Photography, Solar, Motorcycles, Medical Mobility, Emergency Lighting, Hunting, Lawn and Garden Tools, Toys and Hobby, Engine Starters, Power sports, Golf Carts, Security.

3 Pack - Universal Power Group 6V 4.5Ah General 00648 Sealed Non-Spillable Emergency Light Battery WKA6-5F - Weight: 1. 59 lbs.

More information about UPG 6543875488

---

10 Pack - Universal Power Group 6V 4.5Ah General 00648 Sealed Non-Spillable Emergency Light Battery WKA6-5F

UPG - Common uses for the ub645:  consumer electronics, medical mobility, toys and hobby, lawn and Garden Tools, Emergency Lighting, Engine Starters, Golf Carts, Motorcycles, Electric Vehicles, Power sports, Access Control Devices, Photography, Portable Tools, Solar, Hunting, Security. Upg #d5733 ub645 6v 4.

5ah. Pack of 10 Weight: 1. 59 lbs. Ub645 6v 4. 5ah - absorbant glass Mat AGM technology for superior performance. Valve regulated, spill proof construction allows safe operation in any position. Dimensions: 2. 78 inches x 1. 88 inches x 4. 18 inches. Rechargeable battery that can be mounted in any position, resists shocks and vibration.

10 Pack - Universal Power Group 6V 4.5Ah General 00648 Sealed Non-Spillable Emergency Light Battery WKA6-5F - 1 year Warranty. Sla/agm maintenance free, spill proof battery.

More information about UPG


Similar products

---

Mighty Max Battery 6volt 7.2ah Battery Replacement for WKA6-7.2F Brand Product

Mighty Max Battery 6543875373 - Long lasting high performance in high and low temperatures. Backed by a 30 day refund policy and full 1 year warranty. Ml7-6 sla is a 6v 7ah sealed lead Acid SLA rechargeable maintenance free battery. Dimensions: 5. 94 inches x 1. 34 inches x 3. 94 inches. No wire harness or mounting accessories included. Sla / agm spill proof battery has a characteristic of high discharge rate, wide operating temperatures, long service life and deep discharge recover.

Rechargeable battery that can be mounted in any position, resists shocks and vibration. Pack of 10 Weight: 1. 59 lbs. Listing is for the Battery only. Terminal: F1. 1 year Warranty. Rechargeable battery that can be mounted in any position, resists shocks and vibration. Dimensions: 2. 78 inches x 1. 88 inches x 4.

More information about Mighty Max Battery 6543875373


Similar products

Enovize Inc TR-3000 - Up to 3000 watt maximum capacity Voltage Regulator with Step Up or Down Voltage Transformer. It has two output sockets for 110V and single output socket for 220V. It is also equipped with circuit breaker protection so you'll never need to replace fuses on overload. Elc tr-3000 watt step up/step down heavy duty voltage regulator with transformer is a simple plug and play device.

Multiple sockets 2x 110v us standard & 1x 220V Universal Socket - Accept almost any plug except big S Africa. Meter on front shows exact output voltage. Coming to america or moving overseas is no problem when you purchase this highest quality ELC Voltage Converter. It can regulate input voltage from ac 85v-130v or 180v-260v to output voltage: AC 110V+-3-percent or AC220V+-3-percent.

LiteFuze TR-3000 ELC TR-3000 3000 Watt Voltage Regulator with Transformer - Weight: 13. 70 lbs. Dimensions: 7. 75" x 9. 5" x 4. 50", ce certified. Simply, set the input voltage to the country's voltage you will using it in, then connect it to any AC outlet and switch on the transformer. This allows you to use big ticket items like air compressors and table saws.

More information about Enovize Inc TR-3000

---

110V/220V - ELC 5000 Watt Voltage Transformer Converter with Builtin Regulator - Step Up/Down - Circuit Breaker Protection

LiteFuze FBA_TR-5000 - Up to 5000 watt Maximum Capacity. Multiple sockets US standard & Universal Sockets. It is also equipped with circuit breaker protection so you'll never need to replace fuses on overload. You do not need to worry about setting the input voltage with a manual switch, just connect it to any AC voltage outlet and its ready to go.

Circuit breaker protection, convertingbox Technology Lighter Weight, Thick Industrial Heavy Grade Cord. Weight: 22. 70 lbs, dimensions: 11. 25" x 6. 75" x 11. 37", ce certified. Elc tr-5000 watt step up/step down heavy duty voltage regulator with transformer is simple plug and play with auto input voltage detection.

110V/220V - ELC 5000 Watt Voltage Transformer Converter with Builtin Regulator - Step Up/Down - Circuit Breaker Protection - Auto input voltage Selection, Voltage Regulator with Transformer. The voltage regulator function stabilizes the input voltage 90V-260V and outputs both 110V & 220V from their corresponding outlets simultaneously.

More information about LiteFuze FBA_TR-5000


Similar products

---

12 Pack - OREI American USA To European Schuko Germany Plug Adapters CE Certified Heavy Duty

Orei Products 12PKSCHUKO - 5mm diameter grounded adapter Plug. Circuit breaker protection, convertingbox Technology Lighter Weight, Thick Industrial Heavy Grade Cord. This will not convert the voltage from 220V to 110V. Note: this is just a plug adapter and changes the prongs to round pins for European outlets. Converts 2 or 3 pin american Plug To Euro/German Shucko Plug.

Grounded europe adapter type e/f - usa to europe heavy duty Adaptor Plug German Schuko: Converts 2 Or 3 Pin American Plug To Euro/German Shucko Plug. Multiple sockets US standard & Universal Sockets. This is a grounded Adapter Plug. Make sure your items are compatible for use in 220-240V outlets or use with a proper voltage converter.

12 Pack - OREI American USA To European Schuko Germany Plug Adapters CE Certified Heavy Duty - High quality, CE Certified Adapter. Up to 5000 watt Maximum Capacity. Weight: 22. 70 lbs, dimensions: 11. 25" x 6. 75" x 11. 37", ce certified. Note: this is just a plug adapter that changes the prongs to round pins for European outlets.

More information about Orei Products 12PKSCHUKO


Similar products

---

110V/220V - ELC T-2000 2000-Watt Voltage Converter Transformer - Circuit Breaker Protection - Step Up/Down

Enovize Inc T-2000 - For continuous use: 1100W. Weight: 22. 70 lbs, dimensions: 11. 25" x 6. 75" x 11. 37", ce certified. Make sure your items are compatible for use in 220-240V outlets or use with a proper voltage converter. High quality, CE Certified Adapter. Note: this converter is designed only for European/Asian 220V Single Phase, it will not Work with American 220 Dual Phase.

Make sure you multiply x2 the wattage of your item and get a transformer bigger than that. There are a total of three outputs on the front panel. Circuit breaker protection, convertingbox Technology Lighter Weight, Thick Industrial Heavy Grade Cord. The elc t series also features circuit breakers which protect the equipment and the transformer against overload.

110V/220V - ELC T-2000 2000-Watt Voltage Converter Transformer - Circuit Breaker Protection - Step Up/Down - With circuit breaker protection you'll never need to replace fuses. This will not convert the voltage from 220V to 110V. Note: this is just a plug adapter and changes the prongs to round pins for European outlets. Converts 2 or 3 pin american Plug To Euro/German Shucko Plug. Elc series of step up/down voltage transformers offers you a safe, reliable, affordable & convenient solution to converting voltages from 110-120 volt up to 220-240 volt or from 220-240 volt down to 110-120 volt for both home use & industrial applications.

Auto input voltage Selection, Voltage Regulator with Transformer.

More information about Enovize Inc T-2000


Similar products

---

6 Pack - 6PKSCHUKO Heavy Duty Grounded USA American to European German Schuko Outlet Plug Adapter

BlastCase 6PKSCHUKO - For continuous use: 1100W. Up to 2000 watt maximum capacity, heavy duty step Up/Down Voltage Converter Transformer 110/120V 220/240V. This is a grounded Adapter Plug. Auto input voltage Selection, Voltage Regulator with Transformer. Note: this converter is designed only for European/Asian 220V Single Phase, it will not Work with American 220 Dual Phase.

. Make sure your items are compatible for use in 220-240V outlets or use with a proper voltage converter. High quality, CE Certified Adapter. Grounded europe adapter - usa to europe heavy duty Adaptor Plug German Schuko: Converts 2 Or 3 Pin American Plug To Euro/German Shucko Plug. Warning: we do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC.

6 Pack - 6PKSCHUKO Heavy Duty Grounded USA American to European German Schuko Outlet Plug Adapter - Circuit breaker protection, convertingbox Technology Lighter Weight, Thick Industrial Heavy Grade Cord. 5mm diameter grounded adapter Plug. Multiple sockets US standard & Universal Sockets. Will not work in Great Britain, Ireland and Switzerland, Italy. Up to 5000 watt Maximum Capacity. Converts 2 or 3 pin american Plug To Euro/German Shucko Plug.

Make sure you multiply x2 the wattage of your item and get a transformer bigger than that.

More information about BlastCase 6PKSCHUKO


Similar products

---

2-Pack Supershieldz for Apple iPhone 8 / iPhone 7 Privacy Anti-Spy Tempered Glass Screen Protector, Anti-Scratch, Bubble Free + Lifetime Replacement

Supershieldz 5647413472 - 9h hardness, scratch resistant, and Maintains the Original Touch Experience. 5mm diameter grounded adapter Plug. Will not work in Great Britain, Ireland and Switzerland, Italy. Make sure you multiply x2 the wattage of your item and get a transformer bigger than that. Weight: 22. 70 lbs, dimensions: 11. 25" x 6. 75" x 11.

37", ce certified. Make sure your items are compatible for use in 220-240V outlets or use with a proper voltage converter. High quality, CE Certified Adapter. Made from the high quality privacy tempered-glass in portrait viewing modes. For continuous use: 1100W. Multiple sockets US standard & Universal Sockets.

2-Pack Supershieldz for Apple iPhone 8 / iPhone 7 Privacy Anti-Spy Tempered Glass Screen Protector, Anti-Scratch, Bubble Free + Lifetime Replacement - Up to 5000 watt Maximum Capacity. This will not convert the voltage from 220V to 110V. Note: this is just a plug adapter and changes the prongs to round pins for European outlets. Warning: we do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC.

Screen is only visible to persons directly in front of screen.

More information about Supershieldz 5647413472


Similar products

---

110V/220V - Step Up/Down - Circuit Breaker Protection - ELC T-5000 5000-Watt Voltage Converter Transformer

Enovize Inc T-5000 - Warning: we do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC. 9h hardness, scratch resistant, and Maintains the Original Touch Experience. Up to 5000 watt maximum capacity, heavy duty step up/Down Voltage Converter Transformer 110/120V 220/240V.

Screen is only visible to persons directly in front of screen. Hydrophobic and Oleo-phobic coating protect against sweat and reduce fingerprints. This will not convert the voltage from 220V to 110V. Note: this is just a plug adapter and changes the prongs to round pins for European outlets. 5mm diameter grounded adapter Plug.

110V/220V - Step Up/Down - Circuit Breaker Protection - ELC T-5000 5000-Watt Voltage Converter Transformer - Converts 2 or 3 pin american Plug To Euro/German Shucko Plug. Elc series of step up/down voltage transformers offers you a safe, reliable, affordable & convenient solution to converting voltages from 110-120 volt up to 220-240 volt or from 220-240 volt down to 110-120 volt for both home use & industrial applications.

For continuous use: 2500W. With circuit breaker protection you'll never need to replace fuses. Auto input voltage Selection, Voltage Regulator with Transformer. Two are grounded 110v outputs designated for 120 volts with a US standard outlet and the 220 volt only universal outlet which accepts plugs from most countries.

More information about Enovize Inc T-5000


Similar products

---

with Worldwide UK/US/AU/EU European Plug Adapter - 110V/220V - 3 Outlets - 5000 Watt Best International Power Voltage Converter Transformer - Step Up/Down

ELC B01N5WQCE9 - 5mm diameter grounded adapter Plug. There are a total of three outputs on the front panel. For continuous use: 2500W. The elc t series also features circuit breakers which protect the equipment and the transformer against overload. Two are grounded 110v outputs designated for 120 volts with a US standard outlet and the 220 volt only universal outlet which accepts plugs from most countries.

Dual circuit breakers protection for each voltage 120v & 220v 1 x 110v socket, 1 x universal 220V Socket Weight: 12. 5 lbs. Dimensions: 1025" x 8" x 4. 5", ce certified. Max - 2000 watt for 30 mins use. Converts 2 or 3 pin american Plug To Euro/German Shucko Plug. Make sure your items are compatible for use in 220-240V outlets or use with a proper voltage converter.

with Worldwide UK/US/AU/EU European Plug Adapter - 110V/220V - 3 Outlets - 5000 Watt Best International Power Voltage Converter Transformer - Step Up/Down - High quality, CE Certified Adapter. Elc series of step up/down voltage transformers offers you a safe, reliable, affordable & convenient solution to converting voltages from 110-120 volt up to 220-240 volt or from 220-240 volt down to 110-120 volt for both home use & industrial applications. 2 x 110v socket, 1 x universal 220V Socket.

Weight: 22. 70 lbs, dimensions: 11.

More information about ELC B01N5WQCE9


Similar products

---

ELC T-3000 3000-Watt Voltage Converter Transformer - 110V/220V - Circuit Breaker Protection - Step Up/Down

Enovize Inc T-3000 - 2. 5d rounded edge Glass for comfort on the fingers and hand. 2 x 110v socket, 1 x universal 220V Socket. Make sure you multiply x2 the wattage of your item and get a transformer bigger than that. Warning: we do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC.

For continuous use: 2500W. Up to 5000 watt maximum capacity, heavy duty step up/Down Voltage Converter Transformer 110/120V 220/240V. This will not convert the voltage from 220V to 110V. Note: this is just a plug adapter and changes the prongs to round pins for European outlets. This will not convert the voltage from 220V to 110V.

ELC T-3000 3000-Watt Voltage Converter Transformer - 110V/220V - Circuit Breaker Protection - Step Up/Down - Note: this is just a plug adapter and changes the prongs to round pins for European outlets. Warning: we do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC. 5mm diameter grounded adapter Plug. Make sure you multiply x2 the wattage of your item and get a transformer bigger than that.

Converts 2 or 3 pin american Plug To Euro/German Shucko Plug. 5mm diameter grounded adapter Plug. Circuit breaker protection, convertingbox Technology Lighter Weight, Thick Industrial Heavy Grade Cord.

More information about Enovize Inc T-3000


Similar products

---

Circuit Breaker Protection - LiteFuze LT-5000 5000 Watt Voltage Converter Transformer - Step Up/Down - 110V/220V

Enovize Inc LT-5000 - The litefuze lt series 5000 watt step up/step Down heavy duty voltage transformer is equipped with circuit breaker protection so you'll never need to replace fuses on overload. Note: this converter is designed only for European/Asian 220V Single Phase, it will not Work with American 220 Dual Phase. Just multiply the efficiency factor times the max powerwatt rating of your product and then purchase a transformer of atleast that size.

Circuit breaker protection, convertingbox technology Lighter Weight & Noise Reduction, Thick Industrial Heavy Grade Cord Multiple Sockets German/French Shucko Output Socket & Universal Sockets. The efficiency factor of LT series voltage transformers is 1. 5, use this factor to determine the correct size voltage transformer for your electronics/applainces.

Circuit Breaker Protection - LiteFuze LT-5000 5000 Watt Voltage Converter Transformer - Step Up/Down - 110V/220V - 5 year manufacturer's limited Warranty Up to 5000 watt Maximum Capacity. Efficiency factor of 1. 25x. Will not work in Great Britain, Ireland and Switzerland, Italy. Made from the high quality privacy tempered-glass in portrait viewing modes. Make sure you multiply x2 the wattage of your item and get a transformer bigger than that.

Will not work in Great Britain, Italy, Ireland and Switzerland.

More information about Enovize Inc LT-5000


Similar products

---

Rockstone Power 3000 Watt Heavy Duty Step Up/Down Voltage Transformer Converter, 110/120/220/240 V, 5V USB Port

E Depot Express 3000 Watt - Metal Casing. This will not convert the voltage from 220V to 110V. Note: this is just a plug adapter and changes the prongs to round pins for European outlets. Type c - europe & asia, hong kong, uae, type G- UK, Type I - Australia & China. Up to 3000 watt maximum capacity, heavy duty step up/Down Voltage Converter Transformer 110/120V 220/240V.

Converts 2 or 3 pin american Plug To Euro/German Shucko Plug. Rockstone power? takes pride in being an industry leader in Quality, Technology and Innovation, our factory is the global leader and one of the largest manufacturers in the industry. Make sure you multiply x2 the wattage of your item and get a transformer bigger than that.

Rockstone Power 3000 Watt Heavy Duty Step Up/Down Voltage Transformer Converter, 110/120/220/240 V, 5V USB Port - Warning: we do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC. 5mm diameter grounded adapter Plug. 2. 5d rounded edge Glass for comfort on the fingers and hand. Please contact us via email if you have any questions. Made from the high quality privacy tempered-glass in portrait viewing modes.

Dual circuit breakers protection for Each Voltage 120V & 220V.

More information about E Depot Express 3000 Watt


Similar products

SMAKN 2699028942 - Onboard precision miniature voltage transformer. Our aim is to provide top Level Customer Service, so we will try our best to solve any problem. Thank you very much! Onboard precision miniature voltage transformer. Parameter: *pCB board size: 49. 5 mm x19. 4 mm. Feedback: we greatly appreciate your POSITIVE feedback.

Onboard high precision op-amp circuit, the signal is accurately sampling and appropriate compensation, and other functions. Shipping list: *the active phase AC output voltage transformer module x 1. Onboard high precision op-amp circuit, the signal is accurately sampling and appropriate compensation, and other functions.

SMAKN® Voltage Transformer Module Active Single Phase Voltage Sensor Module AC output - Please do not leave negative feedback without asking for help. Modules can be measured within 250V AC voltage, the corresponding analog output can be adjusted. Modules can be measured within 250V AC voltage, the corresponding analog output can be adjusted. Pcb board size: 49. 5 mm x19. 4 mm. Weight:19g.

More information about SMAKN 2699028942

---

JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer for Arduino Raspberry pi

JANSANE - This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation. This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi. Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load.

Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3. 5mm like a headphone jack. Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement and over-current protection. Specification model: sct-013-000 type: non-invasive current transformer core material: ferrite input current: 0~100a ac output mode: 0~50ma leading wire in length: 1m turns ratio: 1: 1800 work voltage: 660 v Resistance Grade: Grade B Max Sampling Resistance: 10 Ω Linearity: ±3% Accurancy: ±1% Work Frequency: 50-1 KHz Work Temperature: -25˚C ~ 70˚C Reference project: Open Energy Monitor Dielectric Strength: 6000V AC/1min Opening Size: 0

JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer for Arduino Raspberry pi - 51 * 051inch / 13 x 13mm two form of output: current output or voltage output a burden resistor needed to add; mechanical strength: opening and closing times, no less than 1000 times 20 ℃ High Quality and Safe: Meet the requirement of flame-retardant characteristics UL94-V0 100% Satisfaction Guarantee 12-Month Warranty; No satisfied, Free reason for return; We could also resend you new one due to quality problem.

More information about JANSANE


Similar products

---

CTYRZCH SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer 100A

CTYRZCH - 1. 5m leading wire, Φ3. 5 3 core plug standard output. Two form of output current, voltage voltage output built-in the sampling resistor. Operating temperature: -25 C ~ +70 C. Non-linearity 3%10%-120% rated input current. Core material: ferrite mechanical strength: opening and closing times, no less than 1000 times 20 c Safety indicators: Dielectric strength 6000V AC/1min Meet UL94-V0 flame retardant properties Operating Temperature: -25 C ~ +70 C Applications: for AC motors, lighting equipment, air compressors and other current measurement, monitoring and protection.

. Package include: 1 x split core current transformer SCT-013-000 This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation. This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi.

CTYRZCH SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer 100A - Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load. Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3.

5mm like a headphone jack. Suitable for lighting equipment, monitoring, air compressors, AC motors, current measurement and over-current protection. Opening size:13mmx13mm.

More information about CTYRZCH


Similar products

---

2 X 30A range Current Sensor ACS712 Module

NewZoll 2699029384 - Pin 5v power supply, on-board power indicator. Pin 5v power supply, on-board power indicator. 30a range current Sensor Module. Output : 100mV/A. Size : 31 x 13mm. 1. 5m leading wire, Φ3. 5 3 core plug standard output. Two form of output current, voltage voltage output built-in the sampling resistor. Operating temperature: -25 C ~ +70 C.

Package included: 2 x 30a range current sensor Module ACS712 This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation. This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi. Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load.

2 X 30A range Current Sensor ACS712 Module - Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3. 5mm like a headphone jack. Suitable for lighting equipment, air compressors, AC motors, monitoring, current measurement and over-current protection. Opening size:13mmx13mm.

Specification:current sensor chips: ACS712ELC-30A. Non-linearity 3%10%-120% rated input current.

More information about NewZoll 2699029384


Similar products

---

3.5mm Stereo Female terminal block panel mount connector 2 pack

KINGDEE INC 6543851416 - 3. 5mm stereo female terminal block bring all 3 pins out to screw terminal blocks for easy connection and prototyping work. Output : 100mV/A. Tuv certificated 3. 81mm pitch terminal blocks provide reliable connections with cables. Used to add a 3. 5mm port where field termination is required. This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation.

This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi. Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load. Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3.

3.5mm Stereo Female terminal block panel mount connector 2 pack - 5mm like a headphone jack. Suitable for lighting equipment, air compressors, AC motors, monitoring, current measurement and over-current protection. Opening size:13mmx13mm. Requires only a standard screw driver to install. Pin 5v power supply, on-board power indicator. 3.

More information about KINGDEE INC 6543851416


Similar products

---

SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer 100A

CTYRZCH - 30a range current Sensor Module. Opening size: 13mm * 13mm, non-linearity 3%10%-120% rated input current. Fits for ac motors, air compressors and other current measurements, lighting equipment, monitoring and protection. Output : 100mV/A. Non-linearity 3%10%-120% rated input current. Tuv certificated 3. 81mm pitch terminal blocks provide reliable connections with cables.

Requires only a standard screw driver to install. Used to add a 3. 5mm port where field termination is required. Clearly marked terminal block provides fast and easy termination. Two form of output current, voltage voltage output built-in the sampling resistor. Pin 5v power supply, on-board power indicator. Specification: model: sct-013-000 type: non-invasive current transformer core material: ferrite input current: 0~100a ac output mode: 0~50ma leading wire in length: 1m turns ratio: 1: 1800 work voltage: 660 v Resistance Grade: Grade B Max Sampling Resistance: 10 Ω Linearity: ±3% Accurancy: ±1% Work Frequency: 50-1 KHz Work Temperature: -25˚C ~ 70˚C Reference project: Open Energy Monitor Dielectric Strength: 6000V AC/1min Opening Size: 0

SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer 100A - 51 * 051inch / 13 x 13mm two form of output: current output or voltage output a burden resistor needed to add; Mechanical strength: opening and closing times, lighting equipment, no less than 1000 times 20 ℃ High Quality and Safe: Meet the requirement of flame-retardant characteristics UL94-V0 Applications: For AC motors, air compressors and other current measurement, monitoring and protection.

More information about CTYRZCH


Similar products

---

SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield for Arduino Uno Mega2560

SunFounder - It's in elegant blue with white contents displayed. 1. 5m leading wire, Φ3. 5 3 core plug standard output. Two form of output current, voltage voltage output built-in the sampling resistor. Operating temperature: -25 C ~ +70 C. Non-linearity 3%10%-120% rated input current. Therefore, this is a perfect choice to make your project more interesting and vivid! For more information, refer to https://www.

Sunfounder. Com/wiki/index. Php?title=i2c_lcd2004 package included 1 x i2c/iic lcd2004 Module This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation. This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi.

SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield for Arduino Uno Mega2560 - Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load. Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3.

5mm like a headphone jack. Suitable for lighting equipment, AC motors, monitoring, air compressors, current measurement and over-current protection. Opening size:13mmx13mm. Output : 100mV/A.

More information about SunFounder


Similar products

---

Current Transformer, DROK 100A/100mA AC Current Transformers, Mini Clip-on Current Sensor, Split Core Amp Transformer Sensing Relay, Easy to Install CT without Power Off

DROK 200072 - The secondary circuit is not allowed open circuit, so please do not install a fuse. This is a mini split base current transformer; it's the smallest one compared to the similar products output 100MA. The diameter of inner hole is 16mm, the accuracy is ≤05 grade,. The ct primary should be connected in series with the test current loop, the secondary should be as work in the short-circuit state 2.

Size : 31 x 13mm. Requires only a standard screw driver to install. 1. 5m leading wire, Φ3. 5 3 core plug standard output. Two form of output current, voltage voltage output built-in the sampling resistor. Operating temperature: -25 C ~ +70 C. Package including: 1x current Transformer This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation.

Current Transformer, DROK 100A/100mA AC Current Transformers, Mini Clip-on Current Sensor, Split Core Amp Transformer Sensing Relay, Easy to Install CT without Power Off - This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi. Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load. Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3.

5mm like a headphone jack.

More information about DROK 200072


Similar products

---

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

Elegoo EL-CP-004 - Component listing: 1pcs 40-pin male to female jumper wires 1pcs 40-pin male to malejumper wires 1pcs 40-pin female to female jumper wires This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation. This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi.

Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load. Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3.

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino - 5mm like a headphone jack. Suitable for lighting equipment, AC motors, monitoring, air compressors, current measurement and over-current protection. Opening size:13mmx13mm. So we can control the quality of our productions by ourselves for you. Packing in a color box. We have always cared about the customer experience and improve the product function details.

Including 1x 40-pin male to female jumper wires, 1X 40-pin male to male jumper wires, 1x40-pin female to female jumper wires. Fits for ac motors, lighting equipment, air compressors and other current measurements, monitoring and protection.

More information about Elegoo EL-CP-004


Similar products

---

SunFounder 2 Channel DC 5V Relay Module with Optocoupler Low Level Trigger Expansion Board for Arduino UNO R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi

SunFounder NA - It can be controlled directly by microcontrollerarduino, AVR, 8051, Raspberry Pi, ARM, MSP430, DSP, PIC, TTL logic. Our ac sensing relay using snap joint structure, it can be fixed to the cable directly through nylon ties. The amp transformer is with Built-in input coil; small and light, easy to install.

Fully enclosed ct, good mechanical properties and environmental resistance, strong voltage isolation capability, safety and reliability. Each cable length: about 20 cm /8-inch. Http://wiki. Sunfounder. Cc/index. Php?title=i2c_LCD2004. Output : 100mV/A. Pin 5v power supply, on-board power indicator. Tuv certificated 3.

SunFounder 2 Channel DC 5V Relay Module with Optocoupler Low Level Trigger Expansion Board for Arduino UNO R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi - 81mm pitch terminal blocks provide reliable connections with cables. Non-linearity 3%10%-120% rated input current. The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers. Two form of output current, voltage voltage output built-in the sampling resistor.

Fits for ac motors, lighting equipment, air compressors and other current measurements, monitoring and protection.

More information about SunFounder NA


Similar products

---

WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino

WINGONEER - Max voltage Range: 25V. Used to add a 3. 5mm port where field termination is required. Opening size: 13mm * 13mm, non-linearity 3%10%-120% rated input current. Arduino avr chips have 10-bit AD, so this module simulates a resolution of 000489v 5v/1023, so the minimum voltage of input voltage detection module is 0

00489vx5=002445v. Voltage input range : dC0-25 VVoltage detection range : DC002445 v-25 vvoltage analog resolution : 000489 voutput interface : ""+ "" connected 5/3. 3v, connect this module with the expansion of board arduino, ""-"" connected gnd, not only makes it easier for you to detect voltage battery, ""s"" connected Arduino AD pinsDC input interface : red terminal positive with VCC, negative with GNDBy 3P connector, can also use the IICLCD1602 LCD to display voltage.

WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino - Package includes 5 x standard voltage Sensor Module For Robot This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation. This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi. Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load.

Input current: 0~100a ac; length of leading wire: 1m; two form of Output: current output or voltage output burden resistor needed to add; Cable Jack: 3. 5mm like a headphone jack.

More information about WINGONEER


Similar products

DROK 090009||F - Module parameters: module properties: non-isolated step-down constant current, constant voltage module CC CV charging module Input voltage : DC 7-40V Output voltage :DC 1. 2-35v continuously adjustable output current: 8A when power tube's temperature exceeds 65 degrees, please add cooling fan Constant current range :0

2-8a adjustable turn lamp current : constant current value * 01 , turn the lamp current and constant value linkage, such as constant current value is 3A, turn the lamp current is set to a constant current is 0.1 times 01 * 3a = 03a. The potentiometercv closed to the input voltage is used to regulate voltage, the potentiometerCC closed to output voltage is used to regulate current CC Indicator : dual color indicator, the green light means fully charged No load is green Output short circuit protection : Yes, charging indicator light is red, constant current Dimensions : 65 * 47 * 23.

DROK 090009||F 24V 12V to 5V 20A Buck Converter, 100W High Current Voltage Converter DC 10-35V 24 v 12 v to DC 5 V Volt Regulator Car LED/Solar Energy Regulated Power Supply Module - 5 mm package include: 1x dc step-down power Converter Module properties: it is a non-isolated step-down constant current, constant voltage module CC CV charging module. Drok dc to dc converter input voltage range is dc 7v-40V, continuously adjustable output voltage range is DC 1. 2v-35v, max output power is 300W.

Current: the buck converter output current is 8A when power tube's temperature exceeds 65 degrees, please add a cooling fan ; the adjustable constant current range is 02-8a.

More information about DROK 090009||F

---

400W DC-DC Constant Current Boost Converter Step-up Power Supply Module LED Driver 8.5-50V to 10-60V

Walfront - Please enhance heat dissipation when current is over 7A Quiescent Current: 10mAwill increase when convert 12V to 20V Constant Current Range: 02a to 12a output power = input voltage*current operating temperature: -40℃ to 85℃if temperature is too high, please enhance heat dissipation Frequency: 150KHz Max.

Conversion efficiency: 96% efficiency is related to input/output voltage, current and voltage difference Over Current Protection: Yes if input current is more than 15A, it will automatic reduce output voltage Reverse Input Protection: No Size: 67×48×28mm/2. 63×1. 89×1. 1"   package includes:  1 x Boost Module Dc 8.

400W DC-DC Constant Current Boost Converter Step-up Power Supply Module LED Driver 8.5-50V to 10-60V - 5v to 50v input voltage, 10v to 60v continuously adjustable output voltage, 15A maximum input current, 12A maximum output current.96% maximum conversion efficiency, stable and reliable performance. You can also use the module as a driver for high power LED lights or voltage regulator for solar panels. This is a dc-dc constant current boost converter power supply module with DC 8.

5-50v voltage input and DC 10-60V output voltage. Specifications:  type: Non-isolated boost module Input Voltage: DC8. 5v to 50v output voltage: dc10v to 60V continuously adjustable, default 19V Max.

More information about Walfront


Similar products

---

eBoot 6 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module

eBoot EXPSFD005794 - Suitable for electric equipment, laptop, digital products, etc. Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A.

Designed with two heat sinks, better dissipation performance. Keep it under 2. 5 a and use the heat sink when working for long hours. Input and output are designed with screw terminals, you can connect or disconnect the wire conveniently. Eboot 6 pack lm2596 dc to DC Buck Converter 3. 0-40v to 1. 5-35v power supply step down module features: Input: DC 3 V to 40 V input voltage must be 1.

eBoot 6 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module - 5 v higher than the output voltage, no boost Output: DC 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A Notes: The input and output interface can not be reversed. Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down.

Quantity: 6 pieces; size: 45 * 20 * 14 mm with potentiometer.

More information about eBoot EXPSFD005794


Similar products

---

bayite 3 Wire 0.36" DC 0~30V Digital Voltmeter Gauge Tester Blue LED Display Panel Mount Car Motorcycle Battery Monitor Volt Voltage Meter with Reverse Polarity Protection Pack of 5

bayite CECOMINOD000239 - Reverse polarity protection: The meter won't burn out if reverse polarity is applied, but the screen will display nothing. Input and output are designed with screw terminals, you can connect or disconnect the wire conveniently. Able to measure the voltage that is below 3V. The screw on the back is used to calibrate the reading.

. 3 wires. Display color: blue. Can be calibrated. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Display: three 036" digital led tube. Measurement Accuracy: 1%. Designed with two heat sinks, better dissipation performance. Features: cutting size: 23mm x 14mm/09" x 055", thickness: 10mm/0

bayite 3 Wire 0.36" DC 0~30V Digital Voltmeter Gauge Tester Blue LED Display Panel Mount Car Motorcycle Battery Monitor Volt Voltage Meter with Reverse Polarity Protection Pack of 5 - 39" mounting hole center distance: 28mm measure voltage: dc 0~30v working Voltage: DC 3V-30V Measurement Accuracy: 1% + / - 2 digit Display: Three 036" digital led tube display color: blue refresh rate: about 500ms / times operating temperature: 14 ~ 149 °F-10 ~ 65 °C Reverse protection: Yes When measured voltage is below 10V: the voltmeter displays two decimal digits, for example, 5.

32v when measured voltage is larger than 10V, for example, the voltmeter displays one decimal digit, 10.

More information about bayite CECOMINOD000239


Similar products

---

DC-DC Buck Converter, Aideepen 20A 300W CC CV Step Down Module DC 6-40V to DC 1.2-36V Adjustable Voltage Constant Current Power Supply Volt Reducer Module with Short Circuit Protection

Aideepen EXPSFD005799 - Application: diy stabilized voltage supply, LED driver, monitor, LED car display, fans, motor, photovoltaic energy, mobile power, solar energy, industrial equipment appliances, etc. Reverse polarity protection: The meter won't burn out if reverse polarity is applied, but the screen will display nothing.

Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down. When there is a big difference between input and output voltage, please decrease power and current.

DC-DC Buck Converter, Aideepen 20A 300W CC CV Step Down Module DC 6-40V to DC 1.2-36V Adjustable Voltage Constant Current Power Supply Volt Reducer Module with Short Circuit Protection - Measurement Accuracy: 1%. Display color: blue. Working voltage: DC 3V-30V. Operating temperature: 14 ~ 149 °F-10 ~ 65 °C. Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. With led indicator, more stable and reliable to use. Suitable for electric equipment, laptop, digital products, etc.

Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost.

More information about Aideepen EXPSFD005799


Similar products

---

DROK 0.39" Current Voltage Tester, DC 4.5-100V Digital Multimeter; 0-50A Volt amperage Meter, Red & Green Dual LED Display, Volt Amp Meter Gauge Panel for Car Automotive

DROK - Besides, this meter can display voltage and current simultaneously in such a tiny size 70mm * 40mm * 30mm. Wide measuring range: the multiple meter has wide measuring range voltage measuring range: DC 4. 5-100v; current measuring range: 0-50A. Suitable for electric equipment, digital products, laptop, etc.

Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. The screw on the back is used to calibrate the reading. What's more, if there is an error, this ampere voltage gauge has voltage calibration potentiometer and current calibration potentiometer, you can adjust them by yourself.

Common-ground design: drok volt amp meter digital is provided with 3 wiring terminal, the power comes from the return circuit, when testing voltage and current, so you don't need extra power supply. Strong interference capability: the current voltage monitor has strong anti-interference capability, safe, it can quickly display refresh rate; with exquisite SMT technology, it has good consistency.

DROK 0.39" Current Voltage Tester, DC 4.5-100V Digital Multimeter; 0-50A Volt amperage Meter, Red & Green Dual LED Display, Volt Amp Meter Gauge Panel for Car Automotive - And this ammeter voltmeter panel owns shell, reliable and dustproof. Wide application: drok dc voltmeter ammeter has handy connection and wide application, it can be applied to monitoring storage battery, for example, DC adjustable power supply, or voltage and current changing state of other device. Plus, no-load cv output constant voltage, when input and output is common grounded, CC output constant current.

Adopting 75v / 80a large current dual mos tube designed step-down board, and gives a stable output.

More information about DROK


Similar products

---

DROK 091016 DC-DC Buck Converter 4-38V Step-down Voltage Regulator Module Adjustable Current 5A Max 75W High Power Volt Power Supply Transformer Board with Constant Current & Voltage

DROK 091016 - Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down. Green light is on when full-charged.

Package includes: 1 X Buck Converter Dc 8. 5v to 50v input voltage, 15a maximum input current, 10v to 60v continuously adjustable output voltage, 12A maximum output current.96% maximum conversion efficiency, stable and reliable performance. Large current 30a connection screw terminals, low ripple, Input and output use high frequency low resistance electrolytic capacitor, more convenient to install.

DROK 091016 DC-DC Buck Converter 4-38V Step-down Voltage Regulator Module Adjustable Current 5A Max 75W High Power Volt Power Supply Transformer Board with Constant Current & Voltage - The buck module has 2 heat sinks that could enhance heat dissipation. If the current value multimeter displays is 4a, the maximum current of the module only can be up to 4A; when the current reach 4A, constant-voltage constant-current red indicator light is on, or the light is off LED indicator light: 1.

Parameterinput voltage: 4-38voutput power: 75WMaxTransfer efficiency: 96%MaxOutput current: adjustabel;5AMax Output voltage: 1. 25-36v constantly adjustable input reverse connection protection: NOShort-circuit protection: YESlimited current of 8A Over-temperature protection: YESitem will stop output automatically How to set current limits: 1.

What's more, this ampere voltage gauge has voltage calibration potentiometer and current calibration potentiometer, if there is an error, you can adjust them by yourself. Common-ground design: drok volt amp meter digital is provided with 3 wiring terminal, when testing voltage and current, the power comes from the return circuit, so you don't need extra power supply.

More information about DROK 091016


Similar products

---

MakerFocus 4pcs 186 50 Charging Board Dual USB 5V 2.4A Mobile Power Bank Module 186 50 Lithium Battery Charger Board with Overcharge Overdischarge Short Circuit Protection DIY USB Power Bank Board

MakerFocus - Led digital display status:The LED digital screen displays the current battery charge while charging. When discharging, the led digital screen displays the current power, and the display is saved in about 30 seconds double-click the button to resume display. The system will provide an accurate battery indication after a complete charge and discharge.

Normal ParametersSize: 6. 5 * 2. 5 * 01cmweight: 108gir of pcm : ≤65 mΩallowed 0v change: YesConstant current: 2. 4adual output current: 5V 2. 4ainput voltage B+ to B-: 3. 0 - 4. 2vcharging cable: support Iphone and Android three USB Cables. Button function: press and hold the button after standby, the LED digital screen displays the power.

MakerFocus 4pcs 186 50 Charging Board Dual USB 5V 2.4A Mobile Power Bank Module 186 50 Lithium Battery Charger Board with Overcharge Overdischarge Short Circuit Protection DIY USB Power Bank Board - Technical specification·Prevent Overcharge ProtectionDetection voltage: 4. 20±005vrelease voltage: 4. 100±005vdetection delay time:.

More information about MakerFocus


Similar products

---

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

Elegoo EL-CP-004 - Able to measure the voltage that is below 3V. With led indicator, more stable and reliable to use. Component listing: 1pcs 40-pin male to female jumper wires 1pcs 40-pin male to malejumper wires 1pcs 40-pin female to female jumper wires Dc 8. 5v to 50v input voltage, 15a maximum input current, 10v to 60v continuously adjustable output voltage, 12A maximum output current.

96% maximum conversion efficiency, stable and reliable performance. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers.

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino - Measure voltage: DC 0~30V. Designed with two heat sinks, better dissipation performance. Aideepen 20a 300w dc step down buck converter. When there is a big difference between input and output voltage, please decrease power and current. Application: diy stabilized voltage supply, LED driver, fans, mobile power, photovoltaic energy, solar energy, motor, LED car display, monitor, industrial equipment appliances, etc.

Effortless wiring & compact design: drok tester multimeter provided with 3 wiring terminal, the power comes from the return circuit, when testing voltage and current, so you don't need extra power supply. Reverse polarity protection: The meter won't burn out if reverse polarity is applied, but the screen will display nothing.

More information about Elegoo EL-CP-004


Similar products

---

4-PACK 5A DC-DC Adjustable Buck Converter 4~38v to 1.25-36v Step Down Power Supply High Efficiency Voltage Regulator Module 4-pack 5a buck

D-PLANET 2699029127 - Nickel-cadmium or nickel-metal hydride battery, lithium batteries, can be used in solar panel/wind turbines etc. Safe protection: the buck regulator is designed with short-circuit protectionlimit current 8A, over-temperature protection, without input reversed connection protection. Cc & cv: the volt transformer is with two working modes of constant voltage and constant current, which would be indicated by the red led indicator.

Note: please kindly note that when buck converter module is used in more than 3A, 35W, please strengthen cooling. Note: the positive pole of the battery is connected to B+ and the negative pole is connected to B-, do not reverse it. Working voltage: DC 3V-30V. With led indicator, more stable and reliable to use.

4-PACK 5A DC-DC Adjustable Buck Converter 4~38v to 1.25-36v Step Down Power Supply High Efficiency Voltage Regulator Module 4-pack 5a buck - Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Besides, this meter can display voltage and current simultaneously in such a tiny size 70mm * 40mm * 30mm. Wide measuring range: the multiple meter has wide measuring range voltage measuring range: DC 4.

5-100v; current measuring range: 0-50A. Aideepen 20a 300w dc step down buck converter. Input voltage: 6v to 40v dc10v to 40V is suggested, Output Current: 20Amax.

More information about D-PLANET 2699029127


Similar products

---

AmazonBasics Premium PLA 3D Printer Filament, 1.75mm, Black, 1 kg Spool, 3 Spools

AmazonBasics AML3032852-30 - Engineered to reduce jamming; resealable storage bag included to protect filament between use. Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. The screw on the back is used to calibrate the reading. Working voltage: DC 3V-30V. Reverse polarity protection: The meter won't burn out if reverse polarity is applied, but the screen will display nothing.

Measurement Accuracy: 1%. Spool's built-in gauge shows percentage of material remaining and approximate length remaining. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. And this ammeter voltmeter panel owns shell, reliable and dustproof. Wide application: drok dc voltmeter ammeter has handy connection and wide application, DC adjustable power supply, it can be applied to monitoring storage battery, for example, or voltage and current changing state of other device.

AmazonBasics Premium PLA 3D Printer Filament, 1.75mm, Black, 1 kg Spool, 3 Spools - Drok voltage converter input voltage range is DC 4-38V, max output current is 5A, output current is adjustable, max output power is 75W. Multifunctional: it can be used as buck converter module with over-current protection; it can also be used as high-power LED constant current driver module; what's more, it can be used as battery charger e.

G. Application: diy stabilized voltage supply, LED car display, LED driver, motor, photovoltaic energy, monitor, industrial equipment appliances, solar energy, mobile power, fans, etc.

More information about AmazonBasics AML3032852-30


Similar products

INSTABOOST - For use with gz sherpas & Lead Acid Yetis and Explorer portable power station. Power up for the long road trip or in advance of your outdoor adventure. 16awg. 1. 2m of Length. 8. 0mm input to 12V car charger.

More information about INSTABOOST

---

Goal Zero 15ft 8mm Extension Cable for Yeti, Boulder and Nomad Products

Goal Zero 98065 - Gauge: 16 gauge. 8mm output Connection. Not compatible with boulder 200 briefcase Solar panel. Extension cord for goal zero Yeti, boulder and Nomadic connections. Can also be used to connect panels to Yeti power stations or Sherpa power Pack to charge. Gives you 15 extra' to connect Goal Zero boulder Or nomadic solar panels to each other.

. Cord length: 15Ft. 8mm input - Goal Zero proprietary connection.

More information about Goal Zero 98065


Similar products

---

Tembo Tusk Skottle Kit, with Burner and Carry Bag. NO Bottle

Tembo Tusk - Gas bottles are not included. The tembotusk skottle can be used to cook anything at home or while camping. Removable support legs for easy transport or storage in the supplied carry bag. Gauge: 16 gauge. Easy to use single burner. Not compatible with boulder 200 briefcase Solar panel. The grill is fabricated in the USA and comes per-seasoned so it can be used immediately.

Skottle stands 28 inches / 71 cm high. The legs have a separate storage bag with a Velcro closure. Wide 18 inches / 45. 7 cm of cooking space. The legs are removable. The carry bag will hold the Skottle pan, burner and up to four 16oz gas bottles. The skottle is designed around an inexpensive "Coleman style" single burner.

Tembo Tusk Skottle Kit, with Burner and Carry Bag. NO Bottle - 8mm output Connection. Full kit, includes skottel grill, 000 btu single burner & skottle carry bag * everything you need to start cooking * Made in the USA * 18" Disc 28" Tall when assembled * Uses standard 1lb propane bottles not included Extension cord for goal zero Yeti, 10, boulder and Nomadic connections.

8mm input - Goal Zero proprietary connection. The burner simply hangs in the frame under the bottom of the Skottle pan. Cord length: 15Ft.

More information about Tembo Tusk


Similar products

---

Goal Zero Anderson to 8mm connector

Goal Zero - For connecting solar panels with anderson Power Pole APP connectors to an 8mm female input on a Goal Zero Yeti or Sherpa Power Pack. Skottle stands 28 inches / 71 cm high. 8mm input - Goal Zero proprietary connection. Not compatible with boulder 200 briefcase Solar panel. 8mm output Connection. Used with: Yeti & Solar.

Product sku: 98054. Be sure to review the details before ordering. Wide 18 inches / 45. 7 cm of cooking space. Non-stick cooking surface. Allows goalzero solar panels with Anderson output to charge Yeti or Sherpa with 8mm inputs. Cord length: 15Ft. Extension cord for goal zero Yeti, boulder and Nomadic connections.

Goal Zero Anderson to 8mm connector - Input: app anderson Power Pole see close up image for orientation. Gauge: 16 gauge. Easy to use single burner. Removable support legs for easy transport or storage in the supplied carry bag. Output: 8mm Male. This adapter allows solar panels with an Anderson output port to charge Yeti or Sherpa with 8mm inputs.

More information about Goal Zero


Similar products

---

Goal Zero Sherpa 100 AC Portable Power Bank

Goal Zero 22050 - Removable support legs for easy transport or storage in the supplied carry bag. Input: app anderson Power Pole see close up image for orientation. 8mm output Connection. Non-stick cooking surface. Cord length: 15Ft. Used with: Yeti & Solar. Skottle stands 28 inches / 71 cm high. Includes apple, get detailed port information, USB-C and USB-C to USB-C.

Perfect for keeping cameras and laptops charged. Qi wireless charging + 2. 4a usb simply place your wireless enabled phone on the top of the Sherpa 100 and charging begins. Gauge: 16 gauge. Airline approved and travel ready, the 94. 72wh power bank is equipped to power phones, tablets, DSLR cameras and laptops - including power-hungry MacBooks.

Goal Zero Sherpa 100 AC Portable Power Bank - Two high speed power delivery ports at 60W each, these USB-C Power Delivery ports provide rapid power for laptops, phones and more. Output: 8mm Male. Not compatible with boulder 200 briefcase Solar panel. Goal zero sherpa 100AC portable power bank is sleek and powerful. Integrated 100w ac take the outlet with you, on the plain or in the wild, for serious power anywhere you need it.

No matter the phone, there's a wicked fast, convenient charging solution for you.

More information about Goal Zero 22050


Similar products

---

Dual Positive/Negative ATC Style Fuse Holder 10 GA with Ring Terminals and Anderson Powerpole Connectors

Valley Enterprises - Easy to use single burner. Includes apple, get detailed port information, USB-C and USB-C to USB-C. Dual positive/negative ATC Style 10 GA Fuse Holder. We're including the cables you need to get the job done and an incredible easy way to store them for later. Output: 8mm Male. Non-stick cooking surface. Dual positive/negative atc style 10 ga fuse holder gold plated 1/4" ring terminals on one end and 45 Amp Powerpole Powerpole connectors on the other Includes 2 ATC style 40 Amp fuses Total cable length: 12 inches Extension cord for goal zero Yeti, boulder and Nomadic connections.

. Wide 18 inches / 45. 7 cm of cooking space. Airline approved and travel ready, the 94. 72wh power bank is equipped to power phones, tablets, DSLR cameras and laptops - including power-hungry MacBooks. Two high speed power delivery ports at 60W each, these USB-C Power Delivery ports provide rapid power for laptops, phones and more.

Dual Positive/Negative ATC Style Fuse Holder 10 GA with Ring Terminals and Anderson Powerpole Connectors - 8mm output Connection. Allows goalzero solar panels with Anderson output to charge Yeti or Sherpa with 8mm inputs. Includes 2 atc style 40 Amp fuses. Used with: Yeti & Solar.

More information about Valley Enterprises


Similar products

---

Goal Zero Boulder 100 Briefcase, 100 Watt Monocrystalline Solar Panel

Goal Zero 32408 - 8mm output Connection. Gold plated 1/4" ring terminals on one end and 45 Amp Powerpole Powerpole connectors on the other. Removable kickstands Collapsible kickstand makes it easy to set up wherever you need it and helps optimize solar angle. Output: 8mm Male. Not compatible with boulder 200 briefcase Solar panel.

Integrated 100w ac take the outlet with you, on the plain or in the wild, for serious power anywhere you need it. Goal zero boulder 100 watt solar panel Briefcase A highly efficient portable solar panel totaling 100 watts, in an easy-to-carry briefcase form. Gauge: 16 gauge. Perfect for keeping cameras and laptops charged.

Goal Zero Boulder 100 Briefcase, 100 Watt Monocrystalline Solar Panel - Qi wireless charging + 2. 4a usb simply place your wireless enabled phone on the top of the Sherpa 100 and charging begins. Removable support legs for easy transport or storage in the supplied carry bag. Optional chainability pair the boulder 100 solar Panel Briefcase with Goal Zero’s easy to use Combiner Cables to chain additional panels together and collect more power from the sun.

Used with: Yeti & Solar. Lightweight, 100-watt monocrystalline solar panel with briefcase folding enclosure. Includes apple, get detailed port information, USB-C and USB-C to USB-C.

More information about Goal Zero 32408


Similar products

---

Goal Zero 6mm Male to Alligator Clamp Cable

Goal Zero 98009 - Skottle stands 28 inches / 71 cm high. Includes apple, get detailed port information, USB-C and USB-C to USB-C. Dual positive/negative ATC Style 10 GA Fuse Holder. Output: alligator clips. Comes with a 1-year limited warranty. 2 x 2. 4a usb ports also included. Easy to use single burner. Non-stick cooking surface. Cord length: 15Ft.

Lightweight, 100-watt monocrystalline solar panel with briefcase folding enclosure. Used with: yeti 150/400, maintainer 10 Wide 18 inches / 45. 7 cm of cooking space. For connecting to a 12v lead acid battery via Alligator clips Extension cord for goal zero Yeti, boulder and Nomadic connections. Total cable length: 12 inches.

Goal Zero 6mm Male to Alligator Clamp Cable - Engineered to solar recharge Goal Zero Yeti Portable Power Stations. Product sku: 98054. Gold plated 1/4" ring terminals on one end and 45 Amp Powerpole Powerpole connectors on the other. 8mm output Connection. No matter the phone, there's a wicked fast, convenient charging solution for you. Input: 6.

More information about Goal Zero 98009


Similar products

---

Dometic CFX 50W 12v Electric Powered Portable Cooler, Fridge Freezer

Dometic CFX-50W - Cfx special electronics with digital temperature display. Dometic cfx compressor portable refrigerator/freezers provide excellent cooling performance, even at extreme ambient temperatures and with minimal power consumption. Input: 6. 0mm. Lightweight, 100-watt monocrystalline solar panel with briefcase folding enclosure.

Fitted with heavy-duty features like reinforced corners, stainless steel Hinges and a robust lid lining, hi-tech cfx refrigerator/freezers can withstand the most demanding of loads. Not compatible with boulder 200 briefcase Solar panel. Ideal for camping, emergency, or off-grid situations. Ensures a safe charging experience.

Dometic CFX 50W 12v Electric Powered Portable Cooler, Fridge Freezer - 3-stage battery protection. Wide 18 inches / 45. 7 cm of cooking space. Extremely efficient and superbly Quiet operation. 2 year Warranty. Includes 2 atc style 40 Amp fuses. Except making ice for drinks. Non-stick cooking surface. Even so, they are remarkably lightweight and easy to transport.

More information about Dometic CFX-50W


Similar products

---

Dicor BT-1834-1 1/8" x 3/4" x 30' Butyl Seal Tape

Dicor BT-1834-1 - Lightweight, 100-watt monocrystalline solar panel with briefcase folding enclosure. 2 x 2. 4a usb ports also included. Dicor butyl tape - Ideal for sealing uniquely shaped joints. Removable support legs for easy transport or storage in the supplied carry bag. Used with: Yeti & Solar. Output: 8mm Male. Because the sealant is on a continuous roll, installer can work fast and be virtually assured that there are no skips or runs in the seal.

No matter the phone, there's a wicked fast, convenient charging solution for you. Apply along unusual patterns. Includes apple, get detailed port information, USB-C and USB-C to USB-C. Dual positive/negative ATC Style 10 GA Fuse Holder. Interactive oled display + four cables included check power in and power out, micro usb, and even set roles for ports.

Dicor BT-1834-1 1/8" x 3/4" x 30' Butyl Seal Tape - Except making ice for drinks. Integrated 100w ac take the outlet with you, on the plain or in the wild, for serious power anywhere you need it. Ideal for camping, emergency, or off-grid situations. Airline approved and travel ready, the 94. 72wh power bank is equipped to power phones, tablets, DSLR cameras and laptops - including power-hungry MacBooks.

More information about Dicor BT-1834-1


Similar products

---

Goal Zero 6mm Output 6' Extension Cable

Goal Zero 90808A - 8mm input - Goal Zero proprietary connection. Installs quickly, without gaps. Output: 8mm Male. Wide 18 inches / 45. 7 cm of cooking space. Input: 6. 0mm. Gauge: 16 gauge. Used with: Yeti & Solar. Integrated 100w ac take the outlet with you, on the plain or in the wild, for serious power anywhere you need it. Removable support legs for easy transport or storage in the supplied carry bag.

Output: 6. 0mm. Noise : 42. 00 dbA. Skottle stands 28 inches / 71 cm high. Product sku: 98054. We're including the cables you need to get the job done and an incredible easy way to store them for later. Comes with a 1-year limited warranty. No ice- ever. Input: app anderson Power Pole see close up image for orientation.

Goal Zero 6mm Output 6' Extension Cable - Cord length: 6 feet. Output: alligator clips. Except making ice for drinks. 2 x 2.

More information about Goal Zero 90808A


Similar products

AJC Battery 6FM18 - Voltage: 12V 12 Volts. Important: you must re-USE: your existing cabling and hardware. Warranty: 1 Year. Note: it is your responsibility to verify the batteries being ordered match the batteries in your unit prior to placing your order. Chemistry: sealed Lead Acid AGM. These are replacement batteries only. Capacity: 18Ah.

This is an ajc brand® replacement for a Enduring 6FM18 12V 18Ah UPS Battery. Battery is compatible with these Brands: Enduring. Disclaimer: our products are not affiliated with or authorized by Enduring. We are not responsible for incorrect orders. Terminals: NB.

More information about AJC Battery 6FM18

---

ExpertPower EXP12180 Lead_Acid_Battery

ExpertPower EXP12180 - Battery type - 12 volt 18 amp 20 Hour Sealed Lead Acid Battery With nuts and bolts. Rugged construction - the high impact resistant battery case is Made Up Of A Non-Conductive ABS Plastic. Whether it's the security of your home, or even just a personal HOBBY, the MOBILITY of your machine, be sure to use the most efficient batteries available.

User friendly - easy installation With a Very Durable And Rugged Construction. Genuine expertpower battery - the Most Trusted And Highest Reviewed Sealed Lead Acid Batteries On Amazon. Expertpower sealed Lead Acid Batteries are made with the highest quality of materials available. This material has a strong Resistance To Shock, Vibration, Chemicals and Heat.

ExpertPower EXP12180 Lead_Acid_Battery - Agm tech - utilizes absorbed glass Mat AGM Technology And Has A Wide Temperature Range. Our lead acid batteries are typically used for: home alarm systems, medical Devices, Uninterruptible Power SupplyUPS, Lighting Equipment, General Electronics, Solar Collectors, Emergency Systems, Electric Scooters, Home Security Systems, Wheelchairs and many Other Applications.

More information about ExpertPower EXP12180


Similar products

Mighty Max Battery 5582711865 - Long lasting high performance in high and low temperatures. Backed by a 30 day refund policy and full 1 year warranty. Listing is for the Battery only. No wire harness or mounting accessories included. Sla / agm spill proof battery has a characteristic of high discharge rate, wide operating temperatures, long service life and deep discharge recover.

Rechargeable battery that can be mounted in any position, resists shocks and vibration. Terminal: F2. Delivering power when you need it, heavy-duty, the mighty Max ML15-12 12 Volt 15 AH uses a state of the art, calcium-alloy grid that provides exceptional performance and service life in both float and cyclic applications.

Mighty Max Battery ML15-12 12V 15AH F2 UPS Backup Bttry Replaces Vision HP12-65W, HP12-65W Brand Product - The ml15-12 is an absorbent glass mat agm technology with a valve regulated design, that can be used in enclosed and indoor environments without leaking or maintenance, providing a superior performance for thousands of models. Mighty max sla batteries are utilized in a wide variety of applications including; consumer Electronics, Emergency Lighting, Engine Starters, Golf Carts, Electric Vehicles, Toys and Hobby, Portable Tools, Power sports, Access Control Devices, Motorcycles, Hunting, Solar, Medical Mobility, Lawn and Garden Tools, Security and more.

Specifications: voltage: 12 voltamperage: 15 AHChemistry: SLA, AGMTerminal: F2Battery Dimensions: 5. 94 in x 3. 89 in x 3. 95 inweight: 9.

More information about Mighty Max Battery 5582711865

---

UPBRIGHT New Global AC/DC Adapter Replacement for Briggs and Stratton B4177GS B&S Battery Charger 12V - 13.5V 750mA 12VDC - 13.5VDC 0.75A - 1A Class 2 Transformer Power Supply Cord Cable Mains PSU

UpBright Briggs Stratton B4177GS Battery Charger - Scp: short Circuit output Protection. Upbright 30 days money back guarantee. In great working Condition. Briggs & stratton battery charger World wide input voltage 100-240VAC 50/60Hz. More Compatibility. Upbright new global ac / dc adapter replacement for briggs and stratton b4177gs b & s b&s battery charger 12v - 13.

5v 750ma 12vdc - 13. 5vdc 075a - 1a class 2 transformer power supply Cord Cable PS Wall Home Charger Mains PSU. Tested units. Ocp: over Current output Protection. Ovp, ocp, scp protection ovp: over voltage output protection. 1 full year service warranty. Input: 100-240vac 50/60hz new type circuit design universal switching mode Power Supply Replaces For OLD Type 120VAC 60Hz Input Class 2 Transformer.

More information about UpBright Briggs Stratton B4177GS Battery Charger


Similar products

---

Briggs and Stratton 705927 Battery Charger

Briggs and Stratton 705927 - World wide input voltage 100-240VAC 50/60Hz. Part # 705927. Genuine replacement part. In great working Condition. Tested units. Contains one Battery charger. Contains one. 1 full year service warranty. Input: 100-240vac 50/60hz new type circuit design universal switching mode Power Supply Replaces For OLD Type 120VAC 60Hz Input Class 2 Transformer.

Scp: short Circuit output Protection. Ovp, ocp, scp protection ovp: over voltage output protection. More Compatibility. Upbright new global ac / dc adapter replacement for briggs and stratton b4177gs b & s b&s battery charger 12v - 13. 5v 750ma 12vdc - 13. 5vdc 075a - 1a class 2 transformer power supply Cord Cable PS Wall Home Charger Mains PSU.

Briggs and Stratton 705927 Battery Charger - Briggs and Stratton genuine part. Upbright 30 days money back guarantee. Ocp: over Current output Protection. This oem part ensures proper fit & performance to maintain the life of your equipment.

More information about Briggs and Stratton 705927


Similar products

---

yueton 12pcs Car Truck Rocker Round Toggle LED Switch On-Off Control, Blue, Green, Yellow, Red

Blovess - Light color: blue, yellow, green, red. Pack of 12, 3 for each color. Input: 12v, 20A. 1 full year service warranty. Input: 100-240vac 50/60hz new type circuit design universal switching mode Power Supply Replaces For OLD Type 120VAC 60Hz Input Class 2 Transformer. Ocp: over Current output Protection. In great working Condition.

Briggs and Stratton genuine part. More Compatibility. Upbright new global ac / dc adapter replacement for briggs and stratton b4177gs b & s b&s battery charger 12v - 13. 5v 750ma 12vdc - 13. 5vdc 075a - 1a class 2 transformer power supply Cord Cable PS Wall Home Charger Mains PSU. Part # 705927. Ovp, ocp, scp protection ovp: over voltage output protection.

yueton 12pcs Car Truck Rocker Round Toggle LED Switch On-Off Control, Blue, Green, Yellow, Red - Scp: short Circuit output Protection. Type: 2 pins 3 pins with LED;. Spst: on-OFF. Contains one Battery charger. Upbright 30 days money back guarantee.

More information about Blovess


Similar products

---

BlastCase Compatible USB Programming Cable for Baofeng Two way Radio UV-5R, BF-888S,BF-F8+ With Driver CD

Baofeng BCEA25 - In great working Condition. Tested units. Upbright 30 days money back guarantee. Input: 12v, 20A. Easy to use, compatible with most radios with 2-pin Mic Connector. Contains one. Part # 705927. 1 full year service warranty. Input: 100-240vac 50/60hz new type circuit design universal switching mode Power Supply Replaces For OLD Type 120VAC 60Hz Input Class 2 Transformer.

Ocp: over Current output Protection. Type: 2 pins 3 pins with LED;. Light color: blue, green, yellow, red. Pack of 12, 3 for each color. Scp: short Circuit output Protection. Ovp, ocp, scp protection ovp: over voltage output protection. Contains one Battery charger. More Compatibility. Upbright new global ac / dc adapter replacement for briggs and stratton b4177gs b & s b&s battery charger 12v - 13.

BlastCase Compatible USB Programming Cable for Baofeng Two way Radio UV-5R, BF-888S,BF-F8+ With Driver CD - 5v 750ma 12vdc - 13. 5vdc 075a - 1a class 2 transformer power supply Cord Cable PS Wall Home Charger Mains PSU. Affordable Price.

More information about Baofeng BCEA25


Similar products

daier Z370 - Over discharge voltage range: 2. 3 3. 0v¡À005v. After the line is connected, Need to charge first, then have output. Attention: do not mix the good battery and poor battery to use. If not same, please fill in each set of batteries and then use. Specification: Over voltage range: 4. 25 4. 35v±005v over discharge voltage range: 2.

3 3. 0v±005v maximum operating current: 0 25a maximum transient current: 34 40a quiescent current: less than 30uA Internal resistance: less than 100m? Working temperature: 40 +50? Storage condition: 40 +80? Effective life: more than30000h Short circuit protection: Yes, delayed self recovery Size: 56mm*45mm*1.

3S 11.1V 12.6V 25A W/Balance 18650 Li ion Lithium Battery PCB Protection Board - 2mmlxwxh material: pcb color: green quantity: 1 pc net weight: 12g note: lighting, display and other factors may cause COLOR SHADING, please comprehensive pictures and text descriptions to determine! Package Includes: 1 x Battery Protection Board Over voltage range: 4. 25 4. 35v¡À005v. Maximum operating current: 0 25A.

Product description features: 100% Brand New and High Quality Strictly according to the diagram wiring: 0VB 3.

More information about daier Z370

---

ZRM&E 40PCS 18650 Lithium Battery Triple Holder Bracket 3 Cell DIY Battery Storage Box Protection Board

- Hight quality fire retardant ABS material, heat resistance, excellent impact resistance, low temperature resistance, chemical resistance and electrical properties. This is 18650 cell container specially used for assembling 18650 li-ion battery. With this holder, storage battery and electric car battery, electric tools battery, which can be used as electric bike battery, we can make different battery pack, etc.

Specification: name: 18650 battery holder Style: 3-cell Material: ABS Color: Black Size: 6075x2025mmapprox Pore Size: 18. 35mm center Distance: 202mm feature: can be freely combined installation: top and bottom piece to work Package: 40pcs 3-Cell 18650 lithium batteries spacer plastic holder bracket Type: 40pcs 3 cell 18650 lithium batteries spacer plastic holder combination mounting bracket.

ZRM&E 40PCS 18650 Lithium Battery Triple Holder Bracket 3 Cell DIY Battery Storage Box Protection Board - . Very good flexibility. Use: suitable for diy combination of import batteries, can hold 3pcs 18650 cells, the unique design and smart solid frame can be an excellent protector for your lithium ion battery pack. Function: type 18650 belong to necessary support of high-end battery combination, high strength support, can withstand high drop, convenient combination, fixed specifications, easy to heat dissipation, and free combination.

Advantage: with card slot at edge, with strong, match up firm, any size can joining together, and no need for other device connected by vibration test. Application: with professional battery holder to replace the traditional general adhesive, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery.

More information about


Similar products

---

14.8V 4S 30A 18650 Lithium Battery BMS PCB Integrated Circuits Protection Board

daier E880 - Interface definition: charging port of the plate and the discharge port is the same, both positive and B connecting battery" ", N, P charging port and port on the negative electrode; B, P pads are all over the hole, the hole diameter of the pad is 3.5mm; the battery charging detection interface with DC output in the form of needle.

Over charging voltage: 4. 08 ± 01. Specifications Over charge detection voltage: 4. 28+ 005 v over charging voltage: 4. 08 ± 01 over discharge voltage: 2. 55±008 over charge detection delay time 01s temperature range? 30/+80? balanced current: 60±5 ma working current: 30A Over current: 75±5A Short circuit protection function: there is, disconnect the load can be self recovery.

14.8V 4S 30A 18650 Lithium Battery BMS PCB Integrated Circuits Protection Board - Do the same mouth when the N is not wiring. Working current: 30A. Over discharge voltage: 2. 55±008. Size:56*45*3mm main function: over charge protection, over current protection function, short circuit protection function, over discharge protection function, balance.

More information about daier E880


Similar products

---

SNNplapla 5 Meter Pure Ni Plate Nickel Strip Tape for Li 18650 Battery Spot Welding Width: 8MM; Thickness: 0.1MM

Xiaoqing-US - Type: 40pcs 3 cell 18650 lithium batteries spacer plastic holder combination mounting bracket. Over discharge voltage: 2. 55±008. Size: 5ml;8mmw;01mmT. Tensile strength: 400-500 N/mm2. Burr: less than 001mm. Quantity: 1 roll 5 Meter Length Nickel Strip Tape. Working current: 30A. Use: suitable for diy combination of import batteries, can hold 3pcs 18650 cells, the unique design and smart solid frame can be an excellent protector for your lithium ion battery pack.

Function: type 18650 belong to necessary support of high-end battery combination, can withstand high drop, fixed specifications, high strength support, easy to heat dissipation, convenient combination, and free combination. Advantage: with card slot at edge, with strong, any size can joining together, match up firm, and no need for other device connected by vibration test.

SNNplapla 5 Meter Pure Ni Plate Nickel Strip Tape for Li 18650 Battery Spot Welding Width: 8MM; Thickness: 0.1MM - Application: with professional battery holder to replace the traditional general adhesive, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery. Its the best choice of the battery combination. Over charge detection voltage: 4. 28+ 005 v.

Description product Name:Pure Nickel Strip Size: 8mm*0

More information about Xiaoqing-US


Similar products

---

Breynet 3M 0.1 x 8 mm 18650 Pure Ni Plate Nickel Welding Strip Tape 3 M For 18650 Battery Spot Welder/Welding

Breynet - Low resistivity good luster, ductility, weldability with anti-abrasion performance Good properties and electrical conductivity on the tin Packing Included:1pc x Nickel strip Type: 40pcs 3 cell 18650 lithium batteries spacer plastic holder combination mounting bracket. Use: suitable for diy combination of import batteries, can hold 3pcs 18650 cells, the unique design and smart solid frame can be an excellent protector for your lithium ion battery pack.

Function: type 18650 belong to necessary support of high-end battery combination, convenient combination, can withstand high drop, easy to heat dissipation, fixed specifications, high strength support, and free combination. Advantage: with card slot at edge, match up firm, any size can joining together, with strong, and no need for other device connected by vibration test.

Breynet 3M 0.1 x 8 mm 18650 Pure Ni Plate Nickel Welding Strip Tape 3 M For 18650 Battery Spot Welder/Welding - Application: with professional battery holder to replace the traditional general adhesive, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery. Its the best choice of the battery combination. Over charge detection voltage: 4. 28+ 005 v.

Over discharge voltage: 2. 55±0

More information about Breynet


Similar products

---

Diymore 5pcs 3S 12V 10A 18650 BMS Charger Module Li-ion Lithium Battery Protection Board

diymore 0122455 - Specification: maximum discharge current: 10A Overcharge detection voltage: 4. 25-4. 35v±005v over-discharge detection voltage: 2. 3-3. 0v±005v maximum working current: 5a-8a; transient current: 9a-10aoperating temperature: -40 ~ 50℃ ; Storage temperature: -40 ~ 80℃ Quiescent current:.

More information about diymore 0122455


Similar products

---

YEHAM 4x5 Cell Spacer 18650 Lithium Battery Plastic Holder Bracket 10pc

YM - Material: abs plastic + poly-carbonate Size Approx: 10 * 8 * 08cm/3. 94" * 3. 15" * 031" pore size: 18. 4 mm suitable for all types of battery assembly type 18650 belong to necessary support of high-end battery combination, can withstand high drop, easy to heat dissipation, convenient combination, high strength support, and free combination With professional battery holder to replace the traditional general adhesive, fixed specifications, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery.

Its the best choice of the battery combination Package include:10 x lithium batteries Plastic holder Type: 40pcs 3 cell 18650 lithium batteries spacer plastic holder combination mounting bracket. Every two 18650 battery cells needs 2 Spacers one up / one down. Overcurrent protection. Low resistivity. Good luster, ductility, weldability.

YEHAM 4x5 Cell Spacer 18650 Lithium Battery Plastic Holder Bracket 10pc - Type 18650 belong to necessary support of high-end battery combination, can withstand high drop, convenient combination, high strength support, fixed specifications, easy to heat dissipation, and free combination. With professional battery holder to replace the traditional general adhesive, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery.

Its the best choice of the battery combination. Over charge detection delay time 0

More information about YM


Similar products

---

Pure Nickel Strip- 0.15x6x50mm 99.6% Nickel for 18650 Soldering Tab for High Capacity Lithium, Li-Po Battery, NiMh and NiCd Battery Pack Battery and Spot Welding, 50 Count, a U.S. Solid Product

U.S. Solid - Quantity: this package comes with 50 pieces of 015x6x50mm pure nickel strips. Battery packs consist of many Lithium-ion cells that are assembled into a pack. For example, an 18650 is around 65 mm 2. 6 in in length, but can be up to 68 mm 2. 7 in long if an internal protection circuit is added. Over charge detection delay time 0

1s. Attention: This is 015 mm pure nickel, if you process it with a battery spot welder and the spots are not reliable, please weld it with a higher power. Working current: 30A. Good properties and electrical conductivity on the tin. Compact size and lightweight. Fine workmanship and durable. Can be applied to various 3.

Pure Nickel Strip- 0.15x6x50mm 99.6% Nickel for 18650 Soldering Tab for High Capacity Lithium, Li-Po Battery, NiMh and NiCd Battery Pack Battery and Spot Welding, 50 Count, a U.S. Solid Product - 7v lithium core. Short circuit protection. Overcharge protection. Over-discharge protection. Use: suitable for diy combination of import batteries, can hold 3pcs 18650 cells, the unique design and smart solid frame can be an excellent protector for your lithium ion battery pack. Function: type 18650 belong to necessary support of high-end battery combination, convenient combination, high strength support, easy to heat dissipation, fixed specifications, can withstand high drop, and free combination.

More information about U.S. Solid


Similar products

---

Baimeixun 20pcs 3x5 Cell Spacer 18650 Lithium Battery Plastic Holder Bracket

Baimeixun - Combination: 3 x 5 Cell. Quantity: this package comes with 50 pieces of 015x6x50mm pure nickel strips. Every two 18650 battery cells needs 2 Spacers one up / one down. Satisfaction guarantee: like all u. S. Every two 18650 battery cells needs 2 Spacers one up / one down. Over discharge voltage: 2. 55±008. Good properties and electrical conductivity on the tin.

Compact size and lightweight. Fine workmanship and durable. Can be applied to various 3. 7v lithium core. Short circuit protection. Good luster, ductility, weldability. Overcurrent protection. Material: abs plastic + poly-carbonate Size Approx: 10 * 6 * 08 cm/3. 94" * 2. 36" * 031" pore size: 18. 4 mm suitable for all types of battery assembly type 18650 belong to necessary support of high-end battery combination, can withstand high drop, and free combination With professional battery holder to replace the traditional general adhesive, fixed specifications, high strength support, easy to heat dissipation, which would brings convenient combination and more firm connection, convenient combination, as well as brings convenient maintenance of the battery.

More information about Baimeixun


Similar products

---

MakerFocus 5pcs Mini Digital DC Voltmeter 0.28 Inch Two-Wire 2.5V-30V Mini Digital DC Voltmeter Voltage Tester Meter 5 Colours

MakerFocus - 5pcs mini digital DC Voltmeter 028 inch two-Wire 2. 5v-30v mini digital dc voltmeter voltage Tester Meter 5 ColoursFeatures:Detection voltage: DC 2. 4v ~ 30vworking current:.

More information about MakerFocus


Similar products

---

ZRM&E 50PCS 18650 Lithium Battery Holder Bracket 1 Cell DIY Battery Storage Box Protection Board

- Suitable for: manufacture nickel-metal hydride batteries, lithium batteries, combination battery and power tools newsletter, special lamps and other industries. Has good weldability, high draw tension, easy to operate. Use: suitable for diy combination of import batteries, can hold 3pcs 18650 cells, the unique design and smart solid frame can be an excellent protector for your lithium ion battery pack.

Function: type 18650 belong to necessary support of high-end battery combination, high strength support, fixed specifications, convenient combination, easy to heat dissipation, can withstand high drop, and free combination. Advantage: with card slot at edge, with strong, any size can joining together, match up firm, and no need for other device connected by vibration test.

ZRM&E 50PCS 18650 Lithium Battery Holder Bracket 1 Cell DIY Battery Storage Box Protection Board - Application: with professional battery holder to replace the traditional general adhesive, which would brings convenient combination and more firm connection, as well as brings convenient maintenance of the battery. Its the best choice of the battery combination. Over charge detection voltage: 4. 28+ 005 v.

Over charge detection delay time 01s.

More information about


Similar products

SMAKN 4350281054 - Our aim is to provide top Level Customer Service, so we will try our best to solve any problem. Thank you very much! Usb intelligent control switch. Onboard high-performance micro-controller chip. Onboard 5v, 10a / 250vac, relay life long continuous pull 100, 10a / 30vdc relay, 000 times. Relay modules with overcurrent protection and freewheeling diode protection.

Pcb size: 47. 6 mm x16. 4 mm. Onboard power LED and relay status LED. Pcb size: 47. 6 mm x16. 4 mm. Usb intelligent control switch. Feedback: we greatly appreciate your POSITIVE feedback. Relay modules with overcurrent protection and freewheeling diode protection. Please do not leave negative feedback without asking for help.

SMAKN® LCUS-1 type USB relay module USB intelligent control switch USB switch - Onboard 5v, 10a / 30vdc relay, relay life long continuous pull 100, 10A / 250VAC, 000 times. Onboard high-performance micro-controller chip. Board ch340 uSB controller chip.

More information about SMAKN 4350281054

---

KNACRO SRD-05VDC-SL-C 2-Way 5V Relay Module Free Driver USB Control Switch PC Intelligent Control

KNACRO 4333091977 - Support win7/xp 32/64-bit systems, easy to use and simple. High-performance USB controller chip, military grade PCB board production. The module uses hid technology, plug and play. Onboard square USB interface connection stable. The module uses HID technology, without any drivers, plug and play. 5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load.

Onboard square USB interface connection stable. Weight:32g/1. 12oz. 5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load. Reserved 4, even if the computer off or unplug the USB from the computer, connected to power, 8-way power interface, you can also relay remains set. Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple.

KNACRO SRD-05VDC-SL-C 2-Way 5V Relay Module Free Driver USB Control Switch PC Intelligent Control - High-performance USB controller chip, military grade PCB board production. Voltage: dc 5v load: 250v 10a ac / dc 30V 10A Max. App download: https://www. Amazon. Com/clouddrive/share/8qn3vw8915jaziv5byzubjWg1Ic4kibOcus1BhTJcrSThe module uses HID technology, without any drivers, plug and play.

More information about KNACRO 4333091977


Similar products

---

KNACRO 1-Channel 5V Relay Module With Square USB interface Plug and Play

KNACRO - Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple. High-performance USB controller chip, military grade PCB board production. Fixed hole size: 3mm, fixed hole center moment: 52. 2mm * 206mm. 5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load. Reserved 4, connected to power, even if the computer off or unplug the USB from the computer, 8-way power interface, you can also relay remains set.

The module uses hid technology, plug and play. Control terminal connection mode: NC / COM / NO. 1-way and 2-way no power connector. If you nedd the soft and C++ code to control this device, just contact us on amazon! App download: https://www. Amazon. Com/clouddrive/share/8qn3vw8915jaziv5byzubjwg1Ic4kibOcus1BhTJcrSThe module uses HID technology, does not require any driver, plug and play.

KNACRO 1-Channel 5V Relay Module With Square USB interface Plug and Play - Pcb size: 56. 5mm * 24. 9mm. Support win7, 64-bit system, easy to use simple. 5v relay, 10a ac load and 30v, the relay can control the large 250v, 10A DC load.

More information about KNACRO


Similar products

---

DZS Elec 5V-30V 1 Channel Wilde Voltage 0-24s Adjustable Delay Internal/External Trigger Relay Board with Timer Delay Conduction Delay Circuit Switch with USB to Micro USB Power Line

DZS Elec 8523903505 - 1-way and 2-way no power connector. If you nedd the soft and C++ code to control this device, just contact us on amazon! The module uses hid technology, plug and play. Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple. High-performance USB controller chip, military grade PCB board production.

. Feature: Size: 5. 4*1. 9*1. 8cm work voltage: wide voltage 5-30v output load: ac 0-220v 10a, dc 0-30V 10A Input Mode: Micro USB interface and solder terminal, two power supply modes. Providing a low pulse signal to external trigger, relay pull and indicator lights up, the output state is: normally open NO and Common interface COM connected, at that moment, or light touch trigger, normally closed NC and the common interfaceCOM is disconnected.

DZS Elec 5V-30V 1 Channel Wilde Voltage 0-24s Adjustable Delay Internal/External Trigger Relay Board with Timer Delay Conduction Delay Circuit Switch with USB to Micro USB Power Line - Operating mode: after powering up the module, the output status: normally open NO and the common interface COM disconnected, normally closed NC and the common terminal COM connected. Support win7, 64-bit system, easy to use simple. 5v relay, 10a ac load and 30v, the relay can control the large 250v, 10A DC load.

Control terminal connection mode: NC / COM / NO. Onboard square USB interface, stable connection. Pcb size: 56.

More information about DZS Elec 8523903505


Similar products

---

type 1 USB relay module USB intelligent switch control - WINGONEER LCUS

WINGONEER® WINGONEER - 5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load. Reserved 4, connected to power, even if the computer off or unplug the USB from the computer, 8-way power interface, you can also relay remains set. Pcb size: 49. 6 mm x16 mm. Fixed hole size: 3mm, fixed hole center moment: 52.

2mm * 206mm. Can adjust 0-24 seconds delay time with potentiometer, which is convenient to complete. Two trigger mode: provide an external signal by TRIG, or light touch trigger button. 5-30v wide work voltage, with terminal and micro USB two power supply modes. With over current protection, strong ability of anti-jamming, pull-up and filter circuit designed mode signal terminal block, suitable for industrial control.

type 1 USB relay module USB intelligent switch control - WINGONEER LCUS - With relay pull indicator light, can directly reflect the current work status. Onboard high-performance micro-controller chips. Onboard ch340 USB control chip. Onboard led power lights and relay status LED lights. Onboard 5 v, 10 a / 250 vac, 10 a / 30 vdc relays, relay's long life can absorb 100000 times in a row.

Module with over-current protection and relay diode current protection function.

More information about WINGONEER® WINGONEER


Similar products

---

LM YN 2-Channel Micro USB Relay Module USB Smart Control Switch

LM YN - 1-way and 2-way no power connector. If you nedd the soft and C++ code to control this device, just contact us on amazon! Onboard 2-way 5v, 10a / 30vdc relays, 10a / 250vac, relay life can be a continuous pull 10 million times; 5. Package included: 1*2-channel Micro USB Relay Module App download: https://www.

Amazon. Com/clouddrive/share/8qn3vw8915JaZiv5bYzuBJWg1Ic4kibOcus1BhTJcrS. Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple. High-performance USB controller chip, military grade PCB board production. Module with overcurrent protection and relay diode freewheeling protection; Hardware introduction and description Board size: 50 * 40mm Board Interface Description: COM1: common; NC1: normally closed; NO1: normally open.

LM YN 2-Channel Micro USB Relay Module USB Smart Control Switch - Features: 1. Open the stc-isp, in hexadecimal hex form send a0 01 01 a2 and a0 02 01 a3 can be opened the first and second relay ; Send in hexadecimal hex A0 01 00 A1 and A0 02 00 A2 can be turned off the first and second relay, SSCOM32 such serial debugging software, select the baud rate of 9600, respectively.

Connect the usb relay module to the computer and install the CH340 USB to serial chip driver 2. Com2: common; nc2: normally closed; NO2: normally open. Pcb size: 49. 6 mm x16 mm.

More information about LM YN


Similar products

---

TEMPer High Accurate USB Thermometer Temperature Sensor Data Logger Record for PC Laptop

Jepeak BE300263 - Onboard ch340 usB control chip;. Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple. High-performance USB controller chip, military grade PCB board production. 5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load. Reserved 4, connected to power, 8-way power interface, even if the computer off or unplug the USB from the computer, you can also relay remains set.

Supply api function for all of win os email, msn remote view data record to file, windows, dynamic curves, alarm with num lock caps lock, mac powered by usb port of your PC Mini size, can directly read temperature through excel or other text files, Linux, this function supports DOS, portable Temperature Range: -40°C ~ 120°C Unit: Degree C/F Temperature can be captured from every second to 12 hours The logged data can be converted to Word / Excel file format easily Dimension: 5.

TEMPer High Accurate USB Thermometer Temperature Sensor Data Logger Record for PC Laptop - 4cm x 1. 4cm x 08cm software support windows xp / 7 package: 1 x USB Thermometer 1 x CD Driver App download: https://www. Amazon. Com/clouddrive/share/8qn3vw8915JaZiv5bYzuBJWg1Ic4kibOcus1BhTJcrS. Waterproof and sensitive sensor. Temperature measurement range: -55 to +125 degrees Celsius/ -67 to +257 degrees Fahrenheit.

More information about Jepeak BE300263


Similar products

---

SainSmart USB 4 Channel Relay Automation 5V

SainSmart 8523716746 - Onboard 2-channel 5v, 10a / 250vac, 10A / 30VDC relays;. 1-way and 2-way no power connector. If you nedd the soft and C++ code to control this device, just contact us on amazon! Datasheet - http://www. Ftdichip. Com/    •led for each relay output    •power led    •usb led    •size - 101*40*16mm    •Windows software examples: VB6, Java netbeans, BCB6, VB.

Net 2010 express, C++. Net 2010 express    •pcb parameters: FR4 / 1. 5mm / two layers / hal / white stamp / metalized holes / solder mask    •extra pcb openings for better voltage isolation    •doubled high current tracks Applications:    • Home automation    • Robotics    • Alarms    • Timers    • Open doors and windows via PC    • Aquariums applications Download: https://s3-ap-northeast-1.

SainSmart USB 4 Channel Relay Automation 5V - Amazonaws. Com/sain-amzn/20/20-018-910/20-018-910 Rar app download: https://www. Amazon. Com/clouddrive/share/8qn3vw8915JaZiv5bYzuBJWg1Ic4kibOcus1BhTJcrS. Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple. High-performance USB controller chip, military grade PCB board production. Module with overcurrent protection and relay diode freewheeling protection;.

More information about SainSmart 8523716746


Similar products

---

ELEGOO 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

ELEGOO EL-CP-004 - 1-way and 2-way no power connector. If you nedd the soft and C++ code to control this device, just contact us on amazon! We have always cared about the customer experience and improve the product function details. Onboard power leD and relay status LED;. Onboard 2-channel 5v, 10a / 250vac, 10A / 30VDC relays;.

The module uses hid technology, does not require any driver, xp 32-bit, plug and play.5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load. Reserved 4, connected to power, 8-way power interface, even if the computer off or unplug the USB from the computer, you can also relay remains set.

ELEGOO 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino - Control electrical devices according weekday/date/time. We have the manufacture factory, making productions and selling by ourselves. Support win7, 64-bit system, easy to use simple. 5v relay, 10a ac load and 30v, the relay can control the large 250v, 10A DC load. Control terminal connection mode: NC / COM / NO.

Onboard square USB interface, stable connection. Pcb size: 56. 5mm * 24.

More information about ELEGOO EL-CP-004


Similar products

---

DVI-I to VGA Adapter, Benfei 2 Pack DVI 24+5 to VGA Male to Female Adapter with Gold Plated Cord

Benfei - The slim dvi & vga connectors with screws not only support secure connection, but also easy plugging & unplugging. Gold-plated connectors to optimize its performance; 5. So you can enjoy hd video or image on the computer monitor, HDTV or big-screen projector. Stable signal transmission: slim dvi & vga connectors with screws not only support secure connection, but also easy plugging & unplugging, Gold-plated connectors to optimize its performance and protect your devices from EMI and lossless signal between devices.

Wide compatibility: this adapter compatible with all dvi-i 24+5 equipped laptops, TVs, desktops, monitors, video cards; and compatible with all VGA equipped Flat Panel Displays, Digital CRT Displays, projectors and displays. Compact, portable and easy to use: quick and easy installation. Description benfei dvi 24+5 dvi-i male to vga female adapter offers you a cost-effective way to connect a HDTV, Projector or Display with VGA to a PC or Mac computer with a DVI Analog Video Card at resolution up to 1080P.

DVI-I to VGA Adapter, Benfei 2 Pack DVI 24+5 to VGA Male to Female Adapter with Gold Plated Cord - Support win7/xp 32/64-bit systems, without any drivers, easy to use and simple. High-performance USB controller chip, military grade PCB board production. Lcus-2 usb relay module equipped with stable performance USB to serial chip and microcontrollers, the computer can be used in the serial port debugging software to send serial port command to control the two relay on and off.

. Free software with many functions.

More information about Benfei


Similar products

---

KNACRO DC-DC Converter Buck Step Down Module 36V 24V 12V 9V 6V-40V to 5V 3A Dual USB Output Car charger Regulators

KNACRO - Waterproof and sensitive sensor. Temperature measurement range: -55 to +125 degrees Celsius/ -67 to +257 degrees Fahrenheit. Email, msn remote view, dynamic curves, Data record to file, alarm. With num lock caps lock, can directly read temperature through excel or other text files, Windows, this function supports DOS, Linux, MAC.

Application range: indoor and outdoor temperature detection, superstore, machine room and storeroom environment monitoring, drugstore air condition temperature control and monitor, farm, vege. High quality, Low cost, No extra power supply. Pcb size: 49. 6 mm x16 mm. 5v relay, the relay can control the maximum 250V 10A AC load and 30V 10A DC load.

KNACRO DC-DC Converter Buck Step Down Module 36V 24V 12V 9V 6V-40V to 5V 3A Dual USB Output Car charger Regulators - Reserved 4, 8-way power interface, connected to power, even if the computer off or unplug the USB from the computer, you can also relay remains set. Onboard ch340 usB control chip;. Dvi-i 24+5 male to vga female ennables you to connect a dvi-i 24+5 port eqipped desktop, projector or projector, video card to a VGA equipped HDTV, laptop, monitor, and support resolution up to 1080P.

1080p full hd video adapter: this dvi vga adapter supports resolution up to 1080P @60Hz. Software examples. So you can enjoy hd video or image on the computer monitor, HDTV or big-screen projector.

More information about KNACRO


Similar products