DZS Elec 6pcs XL6009 DC-DC Booster Converter Module 3V-32V to 5V-35V 4A Adjustable Step-up Voltage Regulator 5V 9V 12V 24V Power Supply Module

#ad
#ad - Attention: input operating voltage should not exceed 32V to avoid damage to the module. Input current: 4a max non-load 18mA The higher voltage, the greater no-load current. The booster power board is equipped with 4A high-efficiency MOSFET switch tube, with the conversion efficiency up to 94%. Ultra high switching frequency 400KHz, the filter capacitance with small capacity can achieve very good effect, smaller ripple and the volume.

If the output voltage is equal to the input voltage or no change in regulation, counterclockwise rotation of the potentiometer a few to a dozen turns, cut off the power, and then power on. Package include: 6pcs xl6009 booster power module xl6009 dc-dc adjustable booster power converter module, High efficiency non-isolated booster module can be used for booster voltage stabilizer power supply, booster charger, DIY adjustable mobile power supply, etc.

Input voltage: 3v-32v, the optimal operating voltage range is 5-32V; Output Voltage: 5V-35V Continuing Adjust Step-up module, output voltage is higher than input voltage. Product name: xl6009 400khz 4a switch current step-on power converter module module type: non-isolation boost boost input voltage: 3V-32V, The optimal operating voltage range is 5-32V Output Voltage: 5V-35V Step-up module, output voltage is higher than input voltage Input Current: 4A max Non-Load 18mA The higher voltage, the greater no-load current.

DZS Elec 6pcs XL6009 DC-DC Booster Converter Module 3V-32V to 5V-35V 4A Adjustable Step-up Voltage Regulator 5V 9V 12V 24V Power Supply Module #ad - Conversion efficiency: max 94% the larger voltage difference, the lower efficiency Switching Frequency: 400KHz Output Ripple: 50mV The higher voltage, the greater current and ripple Load Regulation: +/-05% voltage regulation: +/-05% working temperature: -40 to +85 degree celsius size: 43x21x14mmlxwxh xl6009 booster module is a 4A switching current high performance BOOST module, with the third generation of high frequency switch technology as the core chip, the performance is far superior to LM2577.

More information about #ad

eBoot 6 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module 6 Pack

#ad
eBoot EXPSFD005794 #ad - Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down. Quantity: 6 pieces; size: 45 * 20 * 14 mm with potentiometer.

Keep it under 2. 5 a and use the heat sink when working for long hours. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Eboot 6 pack lm2596 dc to DC Buck Converter 3.

eBoot 6 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module 6 Pack #ad - 0-40v to 1. 5-35v power supply step down module features: Input: DC 3 V to 40 V input voltage must be 1. 5 v higher than the output voltage, no boost Output: DC 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A Notes: The input and output interface can not be reversed. Input: dc 3 v to 40 v input voltage must be 1.

5 v higher than the output voltage, no boost.

More information about eBoot EXPSFD005794 #ad


Similar products



MakerFocus 10pcs TP4056 Charging Module with Battery Protection 18650 BMS 5V Micro USB 1A 186 50 Lithium Battery Charging Board

#ad
MakerFocus . #ad - Makerfocus 10pcs tp4056 charging module with battery protection 18650 bms 5v micro usb 1A 186 50 Lithium Battery Charging BoardDescription:Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery. And still retains the input voltage wiring pads, can be very convenient DIY.

Note: the charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly. Note: the first time you access the battery, it may no voltage between the output OUT + and OUT-, and the battery from the B+ B-, then access 5V voltage charge your energy can activate the protection circuit, then draw a line on the short open also need recharged to activate the protection circuit.

MakerFocus 10pcs TP4056 Charging Module with Battery Protection 18650 BMS 5V Micro USB 1A 186 50 Lithium Battery Charging Board #ad - Tutorial video: https://www. Youtube. Com/watch?v=Qw4psECqpwI. Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge. Micro usb female and next - pads for the power input, access 5V. Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output.

Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A.

More information about MakerFocus . #ad


Similar products



WOWOONE dc to dc Step up Converter DC Voltage Regulator Voltage Converter Step Up dc Boost Converter USB Power Module Supply Module 2V-24V to 5V-28V 2A MT3608 Mico USB Pack of 10

#ad
Eiechip #ad - Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Widely used for storage battery, diy adjustable regulated power supply, power transformers, industrial equipment, 5V, 12V, 28V output, 9V, etc.

Mini dc-dc voltage converter board with micro usB voltage input, just connected with USB power adapter then you can get 9V 12V 18V 24V voltge. We will reply you about any question you ask within 24 hours Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. Charging cut-off voltage: 4.

2v ± 1%; maximum charge current: 1000mA. Input voltage: 5v; battery over-discharge protection voltage: 2. 5v; batteryovercurrent protection current: 3a; connect the battery to the B + B-, inserted into the USB female mobilephone charger, the red light is being charged, the green light to full. The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly.

WOWOONE dc to dc Step up Converter DC Voltage Regulator Voltage Converter Step Up dc Boost Converter USB Power Module Supply Module 2V-24V to 5V-28V 2A MT3608 Mico USB Pack of 10 #ad - We have a strong after-sales service team: as long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Plz click "MakerFocus" and click "Ask a question" to email us! Looking forward to your consultation!

What we pursue is your satisfication of our service, not just for our goods.

More information about Eiechip #ad


Similar products



Zixtec 10 Pack LM2596 DC-DC Buck Converter Step Down Module Power Supply DIP Output 1.25V-30V 3A

#ad
Zixtec #ad - Tutorial video: https://www. Youtube. Com/watch?v=Qw4psECqpwI. Welding, welded directly to the power line input output port; 2. Mt3608 includes under-voltage lockout, current limiting, and thermal overload protection to prevent damage in the event of an output overload. Maximum output current: 2a, board size: 30 x 17 x 14mm/1.

18 x 067 x 055inchl*W*H. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Features: all solid capacitors using sanyo, 36u thick circuit boards, high-Q inductors with high power output LED indicator Size: 45*21*13mm / 1. 69*083*051inch including potentiometersminimum with locating hole with LED indicator DC-DC Instructions: Access to power 3-35V, adjust the blue potentiometer knob clockwise rotation generally boost, buck counterclockwise rotation and with a multimeter to monitor the output voltage reaches the required voltage.

Zixtec 10 Pack LM2596 DC-DC Buck Converter Step Down Module Power Supply DIP Output 1.25V-30V 3A #ad - High-q inductors with high power output LED indicator. 36u thick circuit boards. Inputs with micro usb female, and still retains the input voltage wiring pads, can be directly input to do with the phone charger rechargeable lithium battery, can be very convenient DIY. Package included:  10pcs  x  lm2596s module Input: dc 3 v to 40 v input voltage must be 1.

More information about Zixtec #ad


Similar products



eBoot 10 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module 10 Pack

#ad
eBoot #ad - Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Charging cut-off voltage: 4. 2v ± 1%; maximum charge current: 1000mA. Input voltage: 5v; battery over-discharge protection voltage: 2. 5v; batteryovercurrent protection current: 3a; connect the battery to the B + B-, inserted into the USB female mobilephone charger, the red light is being charged, the green light to full.

The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly. We have a strong after-sales service team: as long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Plz click "MakerFocus" and click "Ask a question" to email us! Looking forward to your consultation!

eBoot 10 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module 10 Pack #ad - Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down.

Widely used for storage battery, 28v output, 9V, DIY adjustable regulated power supply, 12V, 5V, industrial equipment, power transformers, etc. Input voltage range: dc 3. 2v to 35v input voltage must be higher than the voltage output to 1. 5v or more can not be boosted.

More information about eBoot #ad


Similar products



MakerFocus 6pcs 2A 5V Charge Discharge Integrated Module 3.7V 4.2V for 186 50 Lithium Battery Charging Boost Mobile Power Protection PCB Board Module

#ad
Makerfocus . #ad - Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. Note: at this time output voltage 4. 7 / 5v. Mcu users, if you accept a small load key can be connected to the microcontroller about 20s to provide a low level allows the module to continue working. If the load is less than 50ma, the output will be automatically turned off after 30 seconds; if the load is greater than 50MA, the output will be automatically turned on.

Allow discharge while charging. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Lithium battery protection function: over-current, overvoltage, over-temperature, short circuit protection. In discharge mode the charging mode key function is invalid, trigger the KEY port once to open the output; continuously trigger the KEY port twice to close the output.

MakerFocus 6pcs 2A 5V Charge Discharge Integrated Module 3.7V 4.2V for 186 50 Lithium Battery Charging Boost Mobile Power Protection PCB Board Module #ad - The first time the load is connected, the output is automatically turned on. Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down.

Trigger mode: low level trigger ground. Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A.

More information about Makerfocus . #ad


Similar products



150 Pcs 15 Value 100 ohm- 2M ohm Trimpot Variable Resistor 6mm Potentiometer Assortment Kit

#ad
FUNMANY #ad - Note: at this time output voltage 4. 7 / 5v. Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Inputs with micro usb female, can be directly input to do with the phone charger rechargeable lithium battery, and still retains the input voltage wiring pads, can be very convenient DIY.

Quantity: 6 pieces; size: 45 * 20 * 14 mm with potentiometer. Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. Tutorial video: https://www. Youtube. Com/watch?v=Qw4psECqpwI. Wide assortment of values allowing you to get exactly the resistance you need. Note: not suitable for children under 5 years due to small PartsWelcome feel free to contact if you have any question! We suppy the best service ! Input: dc 3 v to 40 v input voltage must be 1.

150 Pcs 15 Value 100 ohm- 2M ohm Trimpot Variable Resistor 6mm Potentiometer Assortment Kit #ad - 5 v higher than the output voltage, no boost. Lithium battery protection function: over-current, overvoltage, over-temperature, short circuit protection. In discharge mode the charging mode key function is invalid, trigger the KEY port once to open the output; continuously trigger the KEY port twice to close the output.

The first time the load is connected, the output is automatically turned on. Dc 2-24v input and 5v-28v adjustable voltage output with high power conversion efficiency up to 93%.

More information about FUNMANY #ad


Similar products



5v Regulator, DROK 5pcs Mini Voltage Reducer DC 4.5-24V 12V 24V Step Down to 5V Buck Converter Board 3A Volt Step-Down Transformer Power Supply Module

#ad
DROK 2001708006 #ad - Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Output current is 3a max please enhance cooling work when it is full load; when real tested input 12V and output is 1. 5a, adjustable range is 08-17v, 2. 5v, no need to add special system. Output integrated adjustable and fixed voltage, you can get fixed output voltage by soldering the pot on the board.

Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. High-q inductors with high power output LED indicator. Brand new and high Quality Variable Resistor Assortment Kit. Mt3608 includes under-voltage lockout, current limiting, and thermal overload protection to prevent damage in the event of an output overload.

5v Regulator, DROK 5pcs Mini Voltage Reducer DC 4.5-24V 12V 24V Step Down to 5V Buck Converter Board 3A Volt Step-Down Transformer Power Supply Module #ad - If the load is less than 50ma, the output will be automatically turned off after 30 seconds; if the load is greater than 50MA, the output will be automatically turned on. Allow discharge while charging. Maximum output current: 2a, board size: 30 x 17 x 14mm/1. 18 x 067 x 055inchl*W*H.

More information about DROK 2001708006 #ad


Similar products



ELEGOO Upgraded Nano V3.0 Plus for Arduino Projects, Nano Board HT42B534-1 /ATmega328P with USB Cable, Compatible with Nano V3.0 x 3 with CableArduino-Compatible

#ad
ELEGOO US-EL-CB-006 #ad - 4 in 1 charging / discharging / lithium battery Protection / Battery Level Indicator Module. Lithium battery protection function: over-current, over-temperature, overvoltage, short circuit protection. In discharge mode the charging mode key function is invalid, trigger the KEY port once to open the output; continuously trigger the KEY port twice to close the output.

The first time the load is connected, the output is automatically turned on. Inputs with micro usb female, can be directly input to do with the phone charger rechargeable lithium battery, and still retains the input voltage wiring pads, can be very convenient DIY. Mt3608 includes under-voltage lockout, current limiting, and thermal overload protection to prevent damage in the event of an output overload.

Technical parameters: microcontroller:atmega328 architecture:avr operating voltage:5 v flash memory:32 kb of which 2 kb used by bootloader sram:2 kb clock speed: 16 mhz analog in pins:8 eeproM:1 KB DC Current per I/O Pins:40 mA I/O Pins Input Voltage:7-9 V Digital I/O Pins:22 6 of which are PWM PWM Output:6 Power Consumption:20 mA Package Include : 3 X Nano Board V3.

ELEGOO Upgraded Nano V3.0 Plus for Arduino Projects, Nano Board HT42B534-1 /ATmega328P with USB Cable, Compatible with Nano V3.0 x 3 with CableArduino-Compatible #ad - 0 plus 3 x usb cable input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost. Mini dc-dc voltage converter board with micro usB voltage input, just connected with USB power adapter then you can get 9V 12V 18V 24V voltge. Input: dc 3 v to 40 v input voltage must be 1. 5 v higher than the output voltage, no boost.

More information about ELEGOO US-EL-CB-006 #ad


Similar products



4-Pack 5A DC-DC Adjustable Buck Converter 4~38v to 1.25-36v Step Down Power Supply High Efficiency Voltage Regulator Module 4-Pack 5a Buck

#ad
D-PLANET 5864305253 #ad - Output: dc 1. 5 v to 35 v voltage is continuously adjustable, maximum output current is 3 A. Adjustment Type: Top Adjustment. They come in a nice storage box, 10pcs for each value. Output current is 3a max please enhance cooling work when it is full load; when real tested input 12V and output is 1. 5a, adjustable range is 0

8-17v, 2. 5v, no need to add special system. Output integrated adjustable and fixed voltage, you can get fixed output voltage by soldering the pot on the board. Three usb cables are included in the package. All boards are well protected in anti-static bags and contained in the outer package together with the cables.

High-q inductors with high power output LED indicator. Package type:15 values, 2kΩ, 100Ω, 20kΩ, 1kΩ, 5kΩ, 300kΩ, 10kΩ, 100kΩ, 500kΩ, 500Ω, 200kΩ, 200Ω, 1mΩ, 2MΩ potentiometer. Package quantity:variable Resistor Assortment Kit 15 Values 150 pcs potentiometers. Trigger mode: low level trigger ground.

4-Pack 5A DC-DC Adjustable Buck Converter 4~38v to 1.25-36v Step Down Power Supply High Efficiency Voltage Regulator Module 4-Pack 5a Buck #ad - Features: all use sanyo solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output. Quantity: 6 pieces; size: 45 * 20 * 14 mm with potentiometer. Widely used for storage battery, power transformers, 12V, DIY adjustable regulated power supply, 28V output, 5V, industrial equipment, 9V, etc.

More information about D-PLANET 5864305253 #ad


Similar products