Go Power! GPC-55-MAX 55 Amp 4-Stage Converter/Battery Charger

Go Power! GPC-55-MAX - The charger is built to charge flooded or wet cell batteries to 100 percent by using 4-stage charging. The second stage is "absorption" where the charger holds the batteries at 14. 4 volts direct current and tapers off the amperage going into the battery. Equalize will charge the batteries to a higher voltage then normal to ensure that both batteries stay at the same charge level.

Compact design to fit in small spaces. The third stage is called "float" when the charger drops the batteries to a lower voltage of 13. 5 volts direct current to avoid excessive gassing of the batteries, this is done so you do not need to constantly fill the distilled water on your battery/batteries. The fourth stage is called "equalize" and this is used when you have more than one battery.

Go Power! GPC-55-MAX 55 Amp 4-Stage Converter/Battery Charger - The "equalize" is done automatically by the charger when the battery bank requires it. Anytime you have more than one battery in a system, the two batteries will end up at different levels of charge. Ul listed. 4-stage battery charging. Great for battery banks with up to 6 batteries. The first stage of charge is called "bulk charge", this is when the charger puts its full output into the batteries.

More information about Go Power! GPC-55-MAX

Go Power! GP-TS 30 Amp Prewired Transfer Switch for Quick Connect

Go Power! GP-TS - Plug and play installation. Prewired 30 amp automatic transfer switch. Delay switch for use with generators. Go power! prewired 30 amp automatic Transfer Switch is used to hardwire inverters into a system where there is an alternative source of AC. Extra outlet wired for charger. This transfer switch is made to only allow one source of AC power to pass through it to the loads and ensures that the inverter will not be damaged if the generator or utility power is hooked up while the inverter is running.

It is prewired for a quick and easy installation to the existing system and also a includes a 15 Amp outlet on the side that is powered by the shore power or generator, permitting to hook up a battery charger without worrying about the inverter running the charger as well as well as contains all instructions.

Go Power! GP-TS 30 Amp Prewired Transfer Switch for Quick Connect - Made for use with inverter, shore power or generators.

More information about Go Power! GP-TS


Similar products



Go Power! TS-30 30 Amp Automatic Transfer Switch

Go Power! TS-30 - Made for use with inverter, shore power or generators. Can handle 2 sources of 30 amps at one time. Single relay. Delay switch for use with generators. Extra outlet wired for charger. Plug and play installation. This transfer switch is made to only allow one source of AC power to pass through it to the loads and can handle 30 Amps of service.

Prewired 30 amp automatic transfer switch. Comes with knockouts for easy and professional installation. Made for use with inverter, shore power or generators. Delay switch for use with generators. This ensures that the inverter will not be damaged if the generator or utility power is hooked up while the inverter is running as well as well as contains all instructions.

Go Power! TS-30 30 Amp Automatic Transfer Switch - Go power! 30 amp transfer switch is used to hardwire inverters into a system where there is an alternative source of AC.

More information about Go Power! TS-30


Similar products



Go Power! TS-50 50 Amp Automatic Transfer Switch

Go Power! TS-50 - This ensures that the inverter will not be damaged if the generator or utility power is hooked up while the inverter is running as well as well as contains all instructions. Can handle 2 sources of 50 amps at one time. Made for use with inverter, shore power or generators. Delay switch for use with generators.

Delay switch for use with generators. Double relay. Single relay. Plug and play installation. Prewired 30 amp automatic transfer switch. Comes with knockouts for easy and professional installation. Delay switch for use with generators. Extra outlet wired for charger. Go power! 50 amp transfer switch is used to hardwire inverters into a system where there is an alternative source of AC.

Go Power! TS-50 50 Amp Automatic Transfer Switch - Can handle 2 sources of 30 amps at one time. Comes with knockouts for easy and professional installation. Made for use with inverter, shore power or generators. Made for use with inverter, shore power or generators. This transfer switch is made to only allow one source of AC power to pass through it to the loads and can handle up to 50 Amps of service.

More information about Go Power! TS-50


Similar products



Renogy MC4 Tool Assembly and Disassembly Tool Solar Panel Cable Crimping Tool for Male/Female MC4 Connectors

TOOL-MC4 TOOL-MC4 - Extra outlet wired for charger. Can handle 2 sources of 30 amps at one time. Very handy for the assembly of custom Mc4 wires. Can handle 2 sources of 50 amps at one time. The mc4 assembly tool is a hard plastic material that is very handy for both the assembly of custom MC4 wires, making it easier for new and veteran users to quickly and easily tighten and take apart the connectors.

Made for use with inverter, shore power or generators. 100% compatible with Renogy MC4 connectors. Single relay. Delay switch for use with generators. Plug and play installation. Comes with knockouts for easy and professional installation. Made for use with inverter, shore power or generators. For breaking connections after they have already been locked together.

Renogy MC4 Tool Assembly and Disassembly Tool Solar Panel Cable Crimping Tool for Male/Female MC4 Connectors - Delay switch for use with generators. Made for use with inverter, shore power or generators. Comes with knockouts for easy and professional installation. Prewired 30 amp automatic transfer switch. Hard plastic.

More information about TOOL-MC4 TOOL-MC4


Similar products



BEP 701 Battery Switches - On-Off

Marinco 701 - Comes with knockouts for easy and professional installation. The continuous and intermittent ratings are tested at 110% of specified ratings. Can handle 2 sources of 50 amps at one time. Comes with knockouts for easy and professional installation. Delay switch for use with generators. Bep marine battery switch test procedures UL 1107 Continuous 1 hour, intermittent 5 minutes and Cranking engine starting - 10 seconds.

This ensures the switch meets ABYC requirements. Extra outlet wired for charger. Three removable side plates provide access of up to 1/0 cables. Made for use with inverter, shore power or generators. Hard plastic. Tin-plated copper studs and nuts. 100% compatible with Renogy MC4 connectors. Double relay. The control knob can be removed by switching to an counterclockwise 45 degree position.

BEP 701 Battery Switches - On-Off - Can handle 2 sources of 30 amps at one time. Operation: on/off, rating: 275a dc continuous 1hr, voltage: 48v dc, 455A DC Intermittent 5 min, 1250a dc cranking 10 sec, Stud Size: 2x3/8" 10mm. Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches.

More information about Marinco 701


Similar products



RENOGY 5 Pair MC4 Male/ Female Solar Panel Cable Connectors Double Seal Rings for Better Waterproof Effect

Renogy 5MC4 - Renogy mc4 male/female solar panel cable connectors five pairs of mc4 solar panel cable connectors ten silver plated copper rated current: 30A Wiring size range: 10, 12 AWG contact resistance: contact material: silver plated copper insulation material: PA/pc warranty information 1-year material warranty.

You can feel that they are heavier & sturdier than other similar products in the market. Description renogy cable connectors are made with highest quality materials. This is to ensure the long term durability.

More information about Renogy 5MC4


Similar products



Blue Sea 9001E E-Series Battery Switch

Acr Electronics 9001E-BSS - This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. Prewired 30 amp automatic transfer switch. Tin-plated copper studs and nuts. Selector 4 position. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits.

Hard plastic. Made for use with inverter, shore power or generators. Up to 350 amperes continuous Rating Ignition protected - safe for installation aboard gasoline powered boats. Very handy for the assembly of custom Mc4 wires. Double relay. Can handle 2 sources of 30 amps at one time. This ensures the switch meets ABYC requirements.

Blue Sea 9001E E-Series Battery Switch - Comes with knockouts for easy and professional installation. Delay switch for use with generators. Ignition protected. Tactile indicator conveys knob position by feel only. Made for use with inverter, shore power or generators.

More information about Acr Electronics 9001E-BSS


Similar products



Go Power GP-ISW-R Industrial Pure Sine Wave Inverter Remote for ISW Inverters

Go Power GP-ISW-R-12 - Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Control your inverter up to 25 feet away. Hard plastic. 25' cable Included. Ignition protected-safe for installation aboard gasoline powered boats. Tin-plated copper studs and nuts.

Extra outlet wired for charger. 100% compatible with Renogy MC4 connectors. This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. Made for use with inverter, shore power or generators. Gp-isw-r-12 go power the gp-isw-r remote featu prewired 30 amp automatic transfer switch.

Go Power GP-ISW-R Industrial Pure Sine Wave Inverter Remote for ISW Inverters - Ignition protected. Plug and play installation. Very handy for the assembly of custom Mc4 wires. Delay switch for use with generators. Ip66 waterproof, iso 8846 and meets ABYC requirements. Delay switch for use with generators. This ensures the switch meets ABYC requirements.

More information about Go Power GP-ISW-R-12


Similar products



SELTERM 10 Pack 4 Gauge 4 AWG 3/8" Stud UL Heavy Duty Copper Crimp Lugs Welding Cable Bare Copper Eyelet Lug

SELTERM - 100% compatible with Renogy MC4 connectors. Copper tubing used for producing the battery cable lugs meet ASTM B 188 electrical grade standard. Comes with knockouts for easy and professional installation. Extra outlet wired for charger. Can handle 2 sources of 50 amps at one time. The copper eyelet connectors are rated for up to 600 volts and tested to ANSI/UL 486 standard.

Control knob can be removed by switching to counter-clockwise 45° position. These connectors are also waterproof and resist dust build up. Ul tested & Approved. Delay switch for use with generators. Continuous rating: 350A, Maximum voltage: 32V DC. Terminal stud size: 3/8" - 16. Prewired 30 amp automatic transfer switch.

SELTERM 10 Pack 4 Gauge 4 AWG 3/8" Stud UL Heavy Duty Copper Crimp Lugs Welding Cable Bare Copper Eyelet Lug - Single relay. Made for use with inverter, shore power or generators. Very handy for the assembly of custom Mc4 wires. Delay switch for use with generators. Heavy duty battery cable lugs from SELTERM are manufactured using industry leading manufacturing processes to guarantee a high-quality product. Can handle 2 sources of 30 amps at one time.

More information about SELTERM


Similar products



Blue Sea Systems Common 150A 10-Gang BusBar with Cover

Blue Sea Systems 53614311 - Continuous rating: 350A, Maximum voltage: 32V DC. These connectors are designed to complete a solar panel PV array, typically in parallel applications. Ip66 waterproof, iso 8846 and meets ABYC requirements. Single relay. Delay switch for use with generators. Comes with knockouts for easy and professional installation.

Made for use with inverter, shore power or generators. Renogy mc4 cable Connectors are made with highest quality materials. Can handle 2 sources of 30 amps at one time. Selector 4 position. 100% compatible with Renogy MC4 connectors. Terminal stud size: 3/8" - 16. Can be Crimped or Soldered. Made for use with inverter, shore power or generators.

Blue Sea Systems Common 150A 10-Gang BusBar with Cover - Close end pad seals Out Moisture Keeping Cables Dry. 150a common busbar with 10 screws and a cover. Delay switch for use with generators. Operation: on/off, 1250a dc cranking 10 sec, voltage: 48v dc, 455A DC Intermittent 5 min, rating: 275a dc continuous 1hr, Stud Size: 2x3/8" 10mm. Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches.

More information about Blue Sea Systems 53614311


Similar products