Jonsson 50 Amp DC Isolator Solar DC Isolator Switch, High Output, Compact, UL Listed,1500V PV DC Battery Disconnect Switch for RVs, Residential, Commercial Solar

#ad
Jonsson APT #ad - Designed for multiple MPPT's. Application: isolator dc switches can be applied to 1-200kw inverter, used for residential or commercial PV Solar Power Systems, Controller, DC Combiner boxes, or For RV Solar Installations. The first dc isolator that complies with AS 60947. 3. 2018 dc-pv2 as well as UL508i. Satisfaction guarantee: we focus on products for Small to Medium Residential or Industrial Contractors.

Ip rating of terminals IP66. Technology leaders: jonnson tech in collaboration with zj beny are proven industry leading specialists in Solar DC Protection Products, endorsed by the Clean energy council of Australia. 10000 cycles no load. Operating tempreature -40 to + 185 degrees faranheit. 90% relative humidity, rated short circuit current 8KA.

Jonsson 50 Amp DC Isolator Solar DC Isolator Switch, High Output, Compact, UL Listed,1500V PV DC Battery Disconnect Switch for RVs, Residential, Commercial Solar #ad - Multiples uses as a battery disconnect switch: RV and Auto. Specifications:  ul listed: e482690 ul508i, 8kv rated impulse withstand voltage. Most compact & hghest voltage output: most compact in the industry, for loads up to 1000 V 50A or 1500V 16A, switches up to 200KW, low temperature rise, durable for long service life.

Rated short duration withstand current 1s 1. 5ka, 50a, dc-pv2.

More information about Jonsson APT #ad

Blue Sea Systems m-Series Mini On-Off Battery Switch with Knob- Red

#ad
Acr Electronics 6006 #ad - Case design allows surface, front panel, or rear panel mounting. Ignition protected, safe for installation aboard gasoline powered boats. Continuous rating: 300A, Maximum Voltage: 48V DC. Single circuit on-off. Switches a single battery to a single load group. Ip66 waterproof, iso 8846 and meets ABYC requirements.

Ignition protected-safe for installation aboard gasoline powered boats. Isolating cover with Snap-On sections protects rear contacts. Mounting hardware not included. Make before break contact design allows switching between battery banks without power interruption.

More information about Acr Electronics 6006 #ad


Similar products



RENOGY 5 Pair MC4 Male/ Female Solar Panel Cable Connectors Double Seal Rings for Better Waterproof Effect

#ad
Renogy 5MC4 #ad - This is to ensure the long term durability. Renogy mc4 male/female solar panel cable connectors five pairs of mc4 solar panel cable connectors ten silver plated copper rated current: 30A Wiring size range: 10, 12 AWG contact resistance: contact material: silver plated copper insulation material: PA/pc warranty information 1-year material warranty.

Description renogy cable connectors are made with highest quality materials. You can feel that they are heavier & sturdier than other similar products in the market.

More information about Renogy 5MC4 #ad


Similar products



Renogy MC4 Y Branch Connectors Solar MC4 Connectors Y connector Solar panel mounts in Pair MMF+FFM

#ad
Renogy CNCT-MC4Y #ad - Continuous rating: 300A, Maximum Voltage: 48V DC. Switches a single battery to a single load group. Use these mc4 branch Connectors to make tight, waterproof connections. Sold as a pair, these "y-connectors" will maintain the voltage of the solar panel configuration to match the battery size. These connectors are also waterproof and resist dust build up.

Ignition protected-safe for installation aboard gasoline powered boats. Contact material: copper, silver plated Flame Class: UL94-V0 or UL94-5VA. Single circuit on-off. These connectors are solely compatible with MC4 connectors and come with one male MMF and one female FFM connector. Protection degree: ip67, mated unmating Force: 200 Newton Insulation Material: PC/PA.

Renogy MC4 Y Branch Connectors Solar MC4 Connectors Y connector Solar panel mounts in Pair MMF+FFM #ad - Renogy mc4 cable Connectors are made with highest quality materials. Make before break contact design allows switching between battery banks without power interruption. Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. These connectors are designed to complete a solar panel PV array, typically in parallel applications.

One ffm; one mmf withstanding voltage: 1000V DCTUV, 600VUL. Renogy mc4 branch connectors are used for parallel wiring solar panels PV modules.

More information about Renogy CNCT-MC4Y #ad


Similar products



Blue Sea Systems MaxiBus 250A BusBar with Six Terminal 18 Studs of 5/16-Inch

#ad
Blue Sea Systems 2126 #ad - Single circuit on-off. Mounting hardware not included. Renogy mc4 cable Connectors are made with highest quality materials. Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. 2 mounting holes accept #10 M5 screws. Switches a single battery to a single load group. Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity.

Continuous rating: 300A, Maximum Voltage: 48V DC. Continuous rating: 250A AC/DC. Protection degree: ip67, mated unmating Force: 200 Newton Insulation Material: PC/PA. This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions.

Blue Sea Systems MaxiBus 250A BusBar with Six Terminal 18 Studs of 5/16-Inch #ad - Compatible with mc4 connectors Also known as MC4 T connectors. Ip66 waterproof, iso 8846 and meets ABYC requirements. Bus material - tin platted copper cda 110/uns c1100 insert molded stainless steel studs eliminate need for securing nut and allow high torqueing for excellent electrical contact Raised bus provides easy access to multiple wires on a single stud.

One ffm; one mmf withstanding voltage: 1000V DCTUV, 600VUL. 250a maxibus busBar with 6 studs.

More information about Blue Sea Systems 2126 #ad


Similar products



SELTERM UL Tinned Copper Wire Lugs Battery Cable Ends - Marine Grade, Heavy Duty

#ad
SELTERM #ad - Compatible with mc4 connectors Also known as MC4 T connectors. Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. These copper lugs are tested to ensure they meet S. A. E conductivity standards J163 & J1811. The pads of the lugs are properly sealed at the ends to prevent any moisture or solder from leaking.

Contact material: copper, silver plated Flame Class: UL94-V0 or UL94-5VA. Renogy mc4 cable Connectors are made with highest quality materials. Rigorous field testing in harsh winter environments in snow have also been conducted by OEMs that depend on these lugs. Designed for durability, and tested to meet s.

SELTERM UL Tinned Copper Wire Lugs Battery Cable Ends - Marine Grade, Heavy Duty #ad - A. E conductivity standards j163 & canadian saftey standards; RoHS 3 & J1811; UL listed to U. S. Selterm marine grade battery cable ends are made from 100% annealed tinned copper, for maximum current flow and a higher degree of conductivity. The copper is malleable & ductile enough to withstand crimp force without cracking.

. Make before break contact design allows switching between battery banks without power interruption. 2 mounting holes accept #10 M5 screws.

More information about SELTERM #ad


Similar products



Blue Sea Systems 5191 Fuse Block Terminal 30-300 AMP

#ad
Acr Electronics 5191 #ad - This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. Provides high current protection in tight space constraints. 250a maxibus busBar with 6 studs. Selterm marine grade battery cable ends are made from 100% annealed tinned copper, for maximum current flow and a higher degree of conductivity.

Ignition protected when used with Blue Sea Systems' MRBF Terminal Fuse. Make before break contact design allows switching between battery banks without power interruption. These ring terminals have a close end pad design, keeping electrical components, batteries and cables safe and free from moisture, and also prevents solder from leaking during installation.

Blue Sea Systems 5191 Fuse Block Terminal 30-300 AMP #ad - Choose from a variety of wire and stud sizes that fits your application; Can be crimped or soldered; Use with compatible Stranded or Fine Stranded Battery or Welding Cables; Full product dimensions provided in the second image. Mounting hardware not included. Ignition protected-safe for installation aboard gasoline powered boats.

These connectors are designed to complete a solar panel PV array, typically in parallel applications. One ffm; one mmf withstanding voltage: 1000V DCTUV, 600VUL. Renogy mc4 cable Connectors are made with highest quality materials. Ignition protected when used with MRBF fuses.

More information about Acr Electronics 5191 #ad


Similar products



Blue Sea Systems e-Series On/Off Battery Switch

#ad
Acr Electronics 9003E-BSS #ad - Ignition protected when used with MRBF fuses. Designed for durability, and tested to meet s. A. E conductivity standards j163 & canadian saftey standards; RoHS 3 & J1811; UL listed to U. S. Terminal stud size: 3/8" - 16. Continuous rating: 250A AC/DC. Compatible with mc4 connectors Also known as MC4 T connectors. Switches a single battery to a single load group.

Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. Single circuit on-off. This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. Ignition protected-safe for installation aboard gasoline powered boats.

Blue Sea Systems e-Series On/Off Battery Switch #ad - Fuses sold separately. These ring terminals have a close end pad design, keeping electrical components, batteries and cables safe and free from moisture, and also prevents solder from leaking during installation. Choose from a variety of wire and stud sizes that fits your application; Can be crimped or soldered; Use with compatible Stranded or Fine Stranded Battery or Welding Cables; Full product dimensions provided in the second image.

Mounting hardware not included. 2 mounting holes accept #10 M5 screws. Insulating cap prevents accidental shorts.

More information about Acr Electronics 9003E-BSS #ad


Similar products



Glarks 125Pcs Marine Grade Heavy Duty Tinned Copper Wire Lugs Battery Cable Ends Eyelets SC Ring Terminal Connectors Assortment Kit

#ad
Glarks #ad - Designed for durability, and tested to meet s. A. E conductivity standards j163 & canadian saftey standards; RoHS 3 & J1811; UL listed to U. S. Continuous rating: 350A, Maximum voltage: 48V DC. Terminal stud size: 3/8" - 16. 250a maxibus busBar with 6 studs. Switches a single battery to a single load group. Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C.

Ignition protected-safe for installation aboard gasoline powered boats. Single circuit on-off. Ignition protected when used with MRBF fuses. Insulating cap prevents accidental shorts. Please check the specific size of the product according to the second picture. Single circuit on-off. Continuous rating: 250A AC/DC.

Glarks 125Pcs Marine Grade Heavy Duty Tinned Copper Wire Lugs Battery Cable Ends Eyelets SC Ring Terminal Connectors Assortment Kit #ad - Ignition protected-safe for installation aboard gasoline powered boats. Fuses sold separately. 2 mounting holes accept #10 M5 screws. Reach compliant. Voltage max operating: 58v dc, terminal stud size: 5/16"-18 8mm, terminal fuses avail.

More information about Glarks #ad


Similar products



SELTERM 10 Pack 6 Gauge 6 AWG 3/8" Stud UL Heavy Duty Copper Crimp Lugs Welding Cable Bare Copper Eyelet Lug

#ad
SELTERM #ad - Mounting hardware not included. Wire can be crimped or soldered to copper lugs, more safe. Application:』 these battery cable lugs are safe and reliable, home applications, solar panels, golf carts, marine, great for distribution box, etc. Selterm bare copper battery cable ends are made from 100% annealed copper, for maximum current flow and a higher degree of conductivity.

Reach compliant. Renogy mc4 cable Connectors are made with highest quality materials. These ring terminals have a close end pad design, batteries and cables safe and free from moisture, keeping electrical components, and also prevents solder from leaking during installation. Choose from a variety of wire and stud sizes that fits your application; Can be crimped or soldered; Use with compatible Stranded or Fine Stranded Battery or Welding Cables; Full product dimensions provided in the second image.

SELTERM 10 Pack 6 Gauge 6 AWG 3/8" Stud UL Heavy Duty Copper Crimp Lugs Welding Cable Bare Copper Eyelet Lug #ad - The lugs are rohs 3 & REACH compliant. Continuous rating: 300A, Maximum Voltage: 48V DC. Contact material: copper, silver plated Flame Class: UL94-V0 or UL94-5VA. The cable lugs are made from 99. 9% pure seamless copper tubes that adhere to the ASTMB188 standard. Continuous rating: 350A, Maximum voltage: 48V DC.

Protection degree: ip67, mated unmating Force: 200 Newton Insulation Material: PC/PA.

More information about SELTERM #ad


Similar products



ENZPOWER IP66 Solar System Solar Combiner Box 32A PV DC Isolator Switch with MC4 Connector for Solar Power System RV, Boats, and Off/On-Grid Solar System

#ad
ENZPOWER #ad - Fuses sold separately. Renogy mc4 cable Connectors are made with highest quality materials. Contact material: copper, silver plated Flame Class: UL94-V0 or UL94-5VA. Padlockable handle- tamper-proof. Continuous rating: 250A AC/DC. Ip66 waterproof, iso 8846 and meets ABYC requirements. What you get:』 in this set, we offer 8 types of SC cold end termination ring terminals total 125pcs for your work, they are sorted packed in a plastic box.

High quality:』 all the sc ring terminals are made of 100% annealed electrolytic grade copper for maximum conductivity, with tinned surface for corrosion protection. Reliable:』 terminals with heavy duty construction improves high temperature durability and closed design seals out the moisture, ensure connection reliability; high standard flared opening for easy wire insertion.

ENZPOWER IP66 Solar System Solar Combiner Box 32A PV DC Isolator Switch with MC4 Connector for Solar Power System RV, Boats, and Off/On-Grid Solar System #ad - Ul approved:』 these marine grade sc ring terminals are UL Approved, comply with all relevant European standards. Continuous rating: 300A, Maximum Voltage: 48V DC. Ignition protected-safe for installation aboard gasoline powered boats. Ignition protected when used with MRBF fuses. Our tinned copper wire lugs are corrosion free; ideal for marine automotive or outdoor use; salt spray tested to ASTMB117 standard.

Load-breaking up to 8 times rated current making it ideal for Solar Panel isolation. Designed for durability, and tested to meet s.

More information about ENZPOWER #ad


Similar products