Ultra Lightweight, Ultra Thin, Up to 248 Degree Arc, for RV, Boats, Roofs, Uneven Surfaces – Renogy 160 Watt 12 Volt Extremely Flexible Monocrystalline Solar Panel

Renogy RNG-160DB-H - Approximately 95% thinner than its rigid counterpart, this panel is ideal for a stealthy solar setup. Highly durable】rigorously tested, the 160w panel is designed to withstand extreme wind of up to 2400Pa and snow loads of up to 5400Pa. The renogy 160 watt 12 volt flexible monocrystalline Solar Panel is the most convenient panel to convert your house from an energy dependent home to an energy producing location.

Monocrystalline 18. 4%. Bypass diodes minimize power drop caused by shade and ensure excellent performance in low-light environments. Potential uses】the renogy 160 watt flexible Monocrystalline Panel can be primarily used on off-grid applications that include rooftop, RV, boats and any curvy surfaces. Extremely flexible】with a flex range of up to 248 degrees, this panel is capable of meeting a wide range of applications where standard panels can be inconvenient to mount, such as on the curved roof of an airstream.

Ultra Lightweight, Ultra Thin, Up to 248 Degree Arc, for RV, Boats, Roofs, Uneven Surfaces - Renogy 160 Watt 12 Volt Extremely Flexible Monocrystalline Solar Panel - Ultra lightweight】thanks to advanced polymer materials, this product weighs 70% less than conventional solar panels, making transportation and installation a breeze. Super thin lamination】discreet and thin, the renogy 160W Lightweight Panel is only a tenth of an inch thick.

More information about Renogy RNG-160DB-H

Renogy 20Ft 10 AWG Solar Panel and Controller Connector Adaptor Wire MC4 Extension Cables

Renogy AK-20FT-10 - The wiring is weatherproof and designed to withstand extreme heat and cold. This wiring kit is essential for off-grid solar installations, roof or ground level, and is offered in a wide range of sizes. This wiring kit is ideal for Renogy Off-Grid Kits ranging from 100W to 400W. The renogy adaptor kit is a set of two wires designed specifically for connecting a Renogy solar panel to a charge controller.

Renogy 20Ft 10 AWG Solar Panel and Controller Connector Adaptor Wire MC4 Extension Cables - Two cables with hard plastic MC4 connecters at one end and bare on the other end male and female. Black wire sunlight resistant cable, extends and locks built-in cables. Uv resistant and waterproof, TUV tested cable. Tuv logo print per feet indicates that the cable meets TUV standards for PV solar application.

Make more space between your solar panels and between your solar panel and charge controller. The adaptor kit includes mc4 connectors on one end for effortless connection to the solar panel, and exposed wire on the other end to lead directly into the charge controller.

More information about Renogy AK-20FT-10


Similar products



RENOGY 5 Pair MC4 Male/ Female Solar Panel Cable Connectors Double Seal Rings for Better Waterproof Effect

Renogy 5MC4 - RENOGY 5 Pair MC4 Male/ Female Solar Panel Cable Connectors Double Seal Rings for Better Waterproof Effect - Description renogy cable connectors are made with highest quality materials. You can feel that they are heavier & sturdier than other similar products in the market. Renogy mc4 male/female solar panel cable connectors five pairs of mc4 solar panel cable connectors ten silver plated copper rated current: 30A Wiring size range: 10, 12 AWG contact resistance: contact material: silver plated copper insulation material: PA/pc warranty information 1-year material warranty.

This is to ensure the long term durability.

More information about Renogy 5MC4


Similar products



Renogy MC4 Tool Assembly and Disassembly Tool Solar Panel Cable Crimping Tool for Male/Female MC4 Connectors

TOOL-MC4 TOOL-MC4 - These connectors are also waterproof and resist dust build up. These connectors are designed to complete a solar panel PV array, typically in parallel applications. Two cables with hard plastic MC4 connecters at one end and bare on the other end male and female. Black wire sunlight resistant cable, extends and locks built-in cables.

Uv resistant and waterproof, TUV tested cable. Tuv logo print per feet indicates that the cable meets TUV standards for PV solar application. Make more space between your solar panels and between your solar panel and charge controller. Renogy mc4 cable Connectors are made with highest quality materials. Hard plastic.

Renogy MC4 Tool Assembly and Disassembly Tool Solar Panel Cable Crimping Tool for Male/Female MC4 Connectors - This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. For breaking connections after they have already been locked together. 100% compatible with Renogy MC4 connectors. The mc4 assembly tool is a hard plastic material that is very handy for both the assembly of custom MC4 wires, making it easier for new and veteran users to quickly and easily tighten and take apart the connectors.

Very handy for the assembly of custom Mc4 wires.

More information about TOOL-MC4 TOOL-MC4


Similar products



Renogy MC4 Y Branch Connectors Solar MC4 Connectors Y connector Solar panel mounts in Pair MMF+FFM

Renogy CNCT-MC4Y - Sold as a pair, these "y-connectors" will maintain the voltage of the solar panel configuration to match the battery size. Use these mc4 branch Connectors to make tight, waterproof connections. These connectors are also waterproof and resist dust build up. Two cables with hard plastic MC4 connecters at one end and bare on the other end male and female.

Black wire sunlight resistant cable, extends and locks built-in cables. Uv resistant and waterproof, TUV tested cable. Tuv logo print per feet indicates that the cable meets TUV standards for PV solar application. Make more space between your solar panels and between your solar panel and charge controller. Renogy mc4 cable Connectors are made with highest quality materials.

Renogy MC4 Y Branch Connectors Solar MC4 Connectors Y connector Solar panel mounts in Pair MMF+FFM - Renogy mc4 branch connectors are used for parallel wiring solar panels PV modules. Protection degree: ip67, mated unmating Force: 200 Newton Insulation Material: PC/PA. Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions.

100% compatible with Renogy MC4 connectors. Very handy for the assembly of custom Mc4 wires.

More information about Renogy CNCT-MC4Y


Similar products



Renogy Adventurer 30A 12V/24V Negative Ground PWM Flush Mount Charge Controller with LCD Display, Compatible with Sealed, Gel, Flooded and Lithium Batteries

Renogy Adventurer 30A 12V/24V - Meet the renogy Adventurer-Li, newly improved with two advanced features. Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions.

Specifications:nominal voltage: 12 vdc/ 24 VDCRated Charge Current: 30AEqualization Voltage: Sealed: 14. 6 v; gel: none; Flooded: 14. 8 vfloat voltage: 13. 8 vself-consumption: ≤13maoperating temperature: -13°f to 131°FEnclosure: IP20Terminals: Up to 8 AWGUSB Output: 5V, 2. 4a maxMax. These connectors are also waterproof and resist dust build up.

Renogy Adventurer 30A 12V/24V Negative Ground PWM Flush Mount Charge Controller with LCD Display, Compatible with Sealed, Gel, Flooded and Lithium Batteries - Protection degree: ip67, mated unmating Force: 200 Newton Insulation Material: PC/PA. Any negative connection on the solar module, battery and load can be safely earth grounded as required. Smart 4 stage pwm charging bulk, boost, overcharging, Float and Equalization and temperature compensation increases battery life and improves system performance.

Very handy for the assembly of custom Mc4 wires. Thanks to its programmable lithium charging voltage, the 30A PWM solar charge controller is now capable of charging most Lithium batteries available on the market. Intelligent protection against: reverse polarity, short-circuit and reverse current.

More information about Renogy Adventurer 30A 12V/24V


Similar products



Link Solar Weatherproof ABS Solar Double Cable Entry Gland for All Cable Types 2mm² to 6mm² for Solar Project on Rv, Campervan, Boat

Link Solar #201809213LS - Contact material: copper, silver plated Flame Class: UL94-V0 or UL94-5VA. This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. Suitable for most round cables for Solar Panel, Aerial, Air conditioning, satellite, DC power, Lighting etc.

Can be fixed with glue not included sikaflex 221 Sikaflex 252, 291, dicor sealant, alike or stainless steel self-tapping screws not included depending on position and sealing requirements etc. The whole set is within 1 ABS white box, 2 cable glands, 2 rubber seals. These connectors are also waterproof and resist dust build up.

Link Solar Weatherproof ABS Solar Double Cable Entry Gland for All Cable Types 2mm² to 6mm² for Solar Project on Rv, Campervan, Boat - Link solar abs solar cable entry gland is used for the passing of cables into the Motorhome, from the Solar panel, or for use on yachts /boats for cable entry from the mast. Very handy for the assembly of custom Mc4 wires. Rs232 port allows communication with BT-1 Bluetooth module and usage of Renogy BT smartphone app.

Designed to cleanly flush mount on walls, providing a sleek, integrated look. An ideal way for routing the cables while mounting solar panels on vehicles and boats, garages, as well as other installations on buildings, sheds etc.100% compatible with Renogy MC4 connectors. This ensure compatibility with any negative ground system, which is the standard and most conventional way of grounding.

More information about Link Solar #201809213LS


Similar products



Renogy 20ft 10AWG Solar Extension Cable with MC4 Male Female Connector

Renogy EXTCB-20FT-10 - An included surface Mount Attachment allows for versatility in mounting. Pg7 waterproof cable gland used for all cable types 2mm² to 6mm² in Dia, Widely used for solar project when routing the cables. These connectors are designed to complete a solar panel PV array, typically in parallel applications. An ideal way for routing the cables while mounting solar panels on vehicles and boats, as well as other installations on buildings, garages, sheds etc.

Hard plastic connectors at each end, female and male connectors. Black wire sunlight resistant cable, extends and locks built-in cables. Uv resistant and waterproof, TUV tested cable. Tuv logo print per feet indicates that the cable meets TUV standards for PV solar application. Make more space between your solar panels and between your solar panel and charge controller.

Renogy 20ft 10AWG Solar Extension Cable with MC4 Male Female Connector - For breaking connections after they have already been locked together. Very handy for the assembly of custom Mc4 wires. These connectors are also waterproof and resist dust build up. Compatible with 12v and 24v system; Deep cycle Sealed, Gel, Flooded and Lithium battery option ready. The adventurer is a negative ground controller.

4a usb port on the front display can be used to charge mobile phones, speakers, tablets, etc.

More information about Renogy EXTCB-20FT-10


Similar products



Renogy 10Ft 10 AWG Solar Panel and Controller Connector Adaptor Wire MC4 Extension Cables

AK-10FT-10 AK-10FT-10 - Intelligent protection against: reverse polarity, short-circuit and reverse current. Backlit lcd screen for displaying operating information and error codes. The adaptor kit includes mc4 connectors on one end for effortless connection to the solar panel, & exposed wire on the other end to lead directly into the charge controller.

Contact material: copper, silver plated Flame Class: UL94-V0 or UL94-5VA. Suitable for most round cables for Solar Panel, satellite, DC power, Air conditioning, Aerial, Lighting etc. Can be fixed with glue not included sikaflex 221 Sikaflex 252, dicor sealant, 291, alike or stainless steel self-tapping screws not included depending on position and sealing requirements etc.

Renogy 10Ft 10 AWG Solar Panel and Controller Connector Adaptor Wire MC4 Extension Cables - The whole set is within 1 ABS white box, 2 cable glands, 2 rubber seals. Compatible with mc4 connectors Also known as MC4 T connectors. One ffm; one mmf withstanding voltage: 1000V DCTUV, 600VUL. 4a usb port on the front display can be used to charge mobile phones, speakers, tablets, etc. Rs232 port allows communication with BT-1 Bluetooth module and usage of Renogy BT smartphone app.

Designed to cleanly flush mount on walls, providing a sleek, integrated look. 100% compatible with Renogy MC4 connectors. Very handy for the assembly of custom Mc4 wires.

More information about AK-10FT-10 AK-10FT-10


Similar products



Renogy BT-1 Bluetooth Module Solar Charge Controller Wireless monitor PV System

Renogy RNG-CTRL-BT-1 - Connect to user-friendly smartphone app, Renogy BT, to keep track of your system. The app is not fully compatible with older versions of the Rover Charge Controller such as version 010403 or 010400 This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions.

Renogy BT-1 Bluetooth Module Solar Charge Controller Wireless monitor PV System - This ensure compatibility with any negative ground system, which is the standard and most conventional way of grounding. Specifications Standby Power Consumption: 004w communication range: ≤15m Cable Length: 5. 00 m 16. 4 ft installation Dimensions: 57. 5, φ3. 2mm 2. 26, φ013in protection grade: ip67 input Voltage: 5V-12V Operating Power Consumption: 0

05w serial baud rate: fixed Baud Rate 9600bps Dimensions: 2. 6 x 2. 01 x 061 in operation temperature: -20℃ to 75℃ -4 F to 167 F Weight: 120 g 4. 2oz two cables with hard plastic MC4 connecters at one end and bare on the other end male and female.

More information about Renogy RNG-CTRL-BT-1


Similar products



Renogy Rover 40 Amp 12V/24V DC Input MPPT Solar Charge Controller Auto Parameter Adjustable LCD Display Solar Panel Regulator fit for Gel Sealed Flooded and Lithium Battery

Renogy RNG-CTRL-RVR40 - Ce and tuv certified hard plastic;protection Class: Class II Temperature Range: -40C~+90 C. Solar input voltage :100VDC Charge circuit voltage drop:≤ 026v discharge circuit voltage drop : ≤ 015v working temperature :-35°C to +45°C Max. Overall Dimension :9. 37 x 6. 81 x 2. 85in. Reverse protection: Any combination of solar module and battery, and Lithium.

0 and ble technology, it features fast and uninterrupted communication. An ideal way for routing the cables while mounting solar panels on vehicles and boats, as well as other installations on buildings, garages, sheds etc. Hard plastic connectors at each end, female and male connectors. Black wire sunlight resistant cable, extends and locks built-in cables.

Renogy Rover 40 Amp 12V/24V DC Input MPPT Solar Charge Controller Auto Parameter Adjustable LCD Display Solar Panel Regulator fit for Gel Sealed Flooded and Lithium Battery - Uv resistant and waterproof, TUV tested cable. Tuv logo print per feet indicates that the cable meets TUV standards for PV solar application. Make more space between your solar panels and between your solar panel and charge controller. Two cables with hard plastic MC4 connecters at one end and bare on the other end male and female.

Black wire sunlight resistant cable, extends and locks built-in cables. Uv resistant and waterproof, TUV tested cable.

More information about Renogy RNG-CTRL-RVR40


Similar products